Failure to follow these warnings and
result in serious injury or death fro
Toddler Bed
OWNER’S MANUAL
Model No. ___________
Serial No. ___________
Dear Customer,
Please fill in the model and
serial numbers above from
the label on the side tube of
your new toddler bed.
Strings can cause strangulation!
DO NOT place items with a string
around a child’s neck, such as
hood strings or pacifier cords. DO
NOT suspend strings over toddler
bed or attach strings to toys.
Model No. 8833
Congratulations on your purchase of a
Graco® toddler bed!
Graco is a leader in juvenile products
designed for your child’s comfort and
convenience. We believe your Graco®
toddler bed is a wise choice, promising
many hours of enjoyment for your child.
Before using your toddler bed, please take
a few minutes to read this Owner’s Manual.
The short time you spend reading these
instructions will help you use your
toddler bed properly.
DO NOT use a water mattress or
all foam mattress with this toddler
bed.
DO NOT place bed
where cords from b
may strangle a chil
fall out of the windo
Please save your Owner’s Manual
for future use.
ALWAYS use a full-size crib mattress, being at least 515/
Customer Satisfaction
8
in. (131 cm) in length, 271/ in. (69 cm) in width, and 4 in.
4
Our goal is to make every product the best it can
be! We are also committed to supporting our
products after purchase. If you would like to speak
to Graco about your product, please contact our
Customer Service Department at 1-800-345-4109
Our knowledgeable staff will be ready to answer any
questions you may have concerning parts, use or
maintenance. When you call, please have the
model and serial numbers ready so your call
may be processed quickly and efficiently.
(10 cm) in thickness.
DISCONTINUE USE OF THE TODDLER BED when your
child weighs more than 50 pounds (23 kg). Use the bed
with only one child at a time.
USE ONLY bed rails provided by Graco®.
© 2000 Graco 602-4-00 602796
2
Assembling the Headboard and Footboard
Attaching the Headboard and Footboard
Step 1.
Step 1.
Legs have a small side hole near
one end. For each leg, push end
with side hole firmly down into
Begin by attaching the frame
to the footboard.
Side hole
a plastic foot. Side hole must be
covered by foot. It may be
necessary to tap foot on a hard
surface to get it all the way on.
Stand the footboard at one
end of the metal frame. (It
does not matter which side of
footboard faces the frame.)
Holding the footboard upright,
grasp the two side tubes as
shown and lift carefully. Rest
the ends of the side tubes on
the footboard.
Step 2.
Assemble headboard and long
legs. Push open end of one long
leg onto plastic plug under “knob”
on one side of headboard.
Then push leg sideways so the
rectangular plug on lower side
of headboard goes into hole on
side of the leg.
Bolt
Step 2.
T-nut
Insert two T-nuts through the
two holes in the side tubes
and into the leg holes as
shown. Place the bolts into
the holes on the outside of the
footboard tubes and into the
T-nuts.
Attach other long leg in the
same way to other side of the
headboard.
Assemble the footboard and
short legs the same way.
Hex
wrench
Step 3.
For footboard (shown at right),
insert a screw into the lowest
Screw
hole on each short leg and into
plastic footboard. For head-
board, insert screws into the
highest hole on each long leg.
Step 3.
With the Graco® name on the
headboard facing away from
the bed frame, attach the side
tubes to the legs as in Step 2
above.
Tighten screw securely with the
included hex wrench, but do
not over-tighten.
Repeat for other three legs.
After the headboard and foot-
board have been attached to
the frame, FIRMLY TIGHTEN
all eight bolts into their T-nuts
with the hex wrench.
CHECK that all four legs are
securely attached to the
head- and footboards by
pulling on the legs.
Hex
wrench
The toddler bed will look like
illustration.
Assembling the Frame
Step 1.
Line up the side tubes and
crossbars on the floor as shown
at right. It may be helpful to
brace one side tube against
a wall or stationary object.
Holes in side tubes must face
each other.
Fold edges
down
Step 4.
Position mattress support
with printed side up as
shown. Fold edges down at
creases, and place on bed
so notches in edges fit over
the crossbars.
Step 2.
Insert ends of the crossbars
into holes in the side tubes.
602-4-00 602796
5
6
Attaching the Bed Rails
Replacement Parts
Instructions for ordering toddler bed parts:
Complete form below. Your toddler bed model number
MUST be included on the form to ensure proper
replacement parts. Your model number can be found
on the label on the side tube of your toddler bed.
Payment must accompany your order.
There are left and right bed rails.
When installed correctly, the
Graco® name on each rail will be
on the outside of the bed.
Step 1.
With the Graco® name facing
away from the bed frame, hold
one bed rail at an angle to the
bed frame as shown. Insert the
curved ends of the bed rail into
the slots at side of headboard.
(The curved ends will match
the shape of the metal leg.)
Parts List:
Price:*
Side tube...................................$ 8.00 (each)
Crossbar................................... $ 5.00 (each)
Long leg....................................$ 7.00 (each)
Short leg................................... $ 5.00 (each)
Foot...........................................$ 5.00 (set of 4)
Hardware.................................. $ 5.00
Mattress support.......................$10.00
Headboard................................$12.00
Footboard................................. $12.00
Left bed rail (as seen from
Step 2.
behind headboard)............... $10.00
Right bed rail (as seen from
Move bed rail toward bed
frame until hole at bottom of
bed rail lines up with the hole
in the center of the side rail.
Put a T-nut into the hole on the
inside of the bed, and use the
hex wrench to screw in a bolt
from the outside.
behind headboard)............... $10.00
Bolt
* Prices subject to change without notice.
Hex
wrench
IF YOU NEED HELP
If you have any questions or if you need
any part not listed, please call toll-free:
1-800-345-4109
T-nut
Return the form below with payment to:
GRACO CHILDREN’S PRODUCTS INC.
CUSTOMER SERVICE DEPARTMENT
P.O. BOX 100, MAIN STREET
Step 3.
Repeat on other side. Both
bed rails must be used.
ELVERSON, PA 19520
Model No. (required)
SHIP TO:
REMINDER: Keep the hex
wrench in a location where
you will be able to find it if
you wish to disassemble
the bed.
Name
Serial No. (required)
Address
Side tube
Crossbar
Long leg
Short leg
City, State, Zip
Foot
Hardware
(
)
Finishing Assembly
Telephone
Mattress support
Headboard
Footboard
Left bed rail
Right bed rail
Place a standard full-size crib
mattress—at least 271/4 inches
(69 cm) wide by 515/8 inches
(131 cm) long by 4 inches
(10 cm) thick—on the finished
toddler bed frame. Your toddler
bed is now ready to use.
Check enclosed
(payable to Graco Children’s
Products Inc.)
Charge to credit card:
Visa
MasterCard
Discover
Subtotal:
Shipping
& handling*:
REMINDER: Before each use,
inspect the toddler bed for
damaged hardware, loose joints,
missing parts, or sharp edges.
Account #:
$5.00
6% sales tax
(PA only):
Expiration date:
Signature:
Total:
*$15.00 outside the continental U.S.
7
8
|