4 IN 1 MULTI
HAIR TRIMMER
MT 6740
_________________________________________________________
DEUTSCH
ENGLISH
FRANÇAIS
PORTUGUÊS
ESPAÑOL
POLSKI
4- 17
18 - 29
30 - 41
42 - 53
54 - 65
66 - 77
78 - 89
90 - 101
102 - 113
ČESKY
TÜRKÇE
ΕΛΛΗΝΙΚA
3
_______________________________________________
SAFETY
7
Please note the following instructions
when using the appliance:
Always disconnect the power
supply unit if the appliance is
not being charged or used.
7
The appliance is designed for
7
domestic use only.
If not already present, for addi-
tional protection it is recommend
to install a residual-current-oper-
ated protective device (RCD)
with a rated residual operating
current not exceeding 30 mA in
the electrical circuit of your bath-
room. Ask your electrician for
advice.
7
Observe these instructions in
order to prevent damage to the
appliance or danger arising
from improper use. Keep them
in a safe place.
7
Never use the appliance in the
bath, shower or over a wash
basin filled with water; nor
should it be operated with wet
hands.
7
7
7
Never use the appliance if it is
visibly damaged.
Keep the appliance away from
children.
Do not open the appliance
under any circumstances. No
warranty claims are accepted
for damage caused by incorrect
handling.
7
Do not immerse the appliance in
water or let it come into contact
with water, even during
cleaning.
7
Do not drop the appliance.
ENGLISH
18
__________________________________________
OVERVIEW
See the illustrations on page 2.
H
Extendable plug-in comb
system suitable for both cutting
widths, with precise trimming
grade display for hair lengths
of 2, 4, 6, 8, 10, 12, 14 and
16 mm.
Controls
A
Professional cutting head
made from industrial ceramic
(width 38 mm).
B
Side catches for removing
attachments.
I
Thinning comb for 2 mm
cutting length.
C
On/off switch.
J
Shaving attachment with single
blade foil for a smooth shave.
D
Charging display (LED). Lights
up red when charging and
green when it is fully charged.
K
Power supply unit.
Other accessories
E
F
Socket for plugging into the
charging unit or connecting the
power supply unit.
1 x two combs.
1 x cleaning brush.
1 x oil for cutting head.
Charging unit.
Accessories
G
Beard trimming attachment
(width 30 mm).
ENGLISH
19
___________________________________
POWER SUPPLY
7
Charging time is approx. 12
hours when the appliance is
switched off. If you switch on the
appliance while it is charging,
charging will stop.
Rechargeable battery
operation
When operating the appliance with
the built-in nickel metal hydride
battery, only use the power unit
supplied for charging.
D
– The charging display
pears.
disap-
Check if the mains voltage on the
type plate of the power supply unit
supplied corresponds to your local
mains supply.
7
7
The ambient temperature should
be between 5 °C and 40 °C.
When fully charged, the appliance
works for around 60 minutes.
It is not advisable to charge the
batteries after every use, especially
if you do not use the appliance for
the full 60 minutes. Only charge
the batteries when they are
completely discharged. This
increases their service life. Do not
charge it every day.
1 Plug the power cord into the
E
appliance socket
and the
power supply unit into the wall
socket.
Notes
7
Charge up the batteries comp-
letely before you use them for the
first time or if you have not used
them for a long time (approx. 12
hours’ timer-controlled charging).
D
– The charging display
lights
up red when charging and
changes to green when it is
fully charged.
ENGLISH
20
___________________________________
POWER SUPPLY
Using the charging unit
E
Mains operation
(with the power supply
1 Put the socket
of the
unit)
appliance into the charging unit.
2 Plug the power cord into the
Check if the mains voltage on the
type plate of the power supply unit
supplied corresponds to your local
mains supply.
socket on the charging unit.
3 Plug the power supply unit into
the wall socket.
The only way to disconnect the
device from the mains is to unplug
the power supply unit.
1 Plug the power supply unit into
E
the socket
on the appliance.
2 Plug the power supply unit into
the wall socket.
Caution
7
When in the bathroom or beside
a water connection, you must
only use the appliance in battery
mode; never run it from the
mains.
ENGLISH
21
________________________________________
Function 1
OPERATION
Special features
This appliance has four separate
functions:
Trimming hair ...
... using the ceramic cutting head
– Function 1: precise hair trimming
at a width of 38 mm.
A
(width 38 mm).
– Function 2: precise beard
trimming at a width of 30 mm.
– Function 3: hair or beard
trimming with various cutting
lengths (2, 4, 6, 8, 10, 12, 14,
16 mm) at widths of 38 mm or
30 mm.
– Function 4: close shaving.
1 If necessary, remove the attach-
ment by pressing in both side
B
Switching on and off
catches
and lifting off.
A
2 Insert ceramic cutting head
C
1 Press the button
to switch on
carefully at the top and press
down until it clicks into place.
the appliance.
C
2 Press the button
to switch off
3 Place a towel around the neck
and shoulder of the person
the appliance.
whose hair you are trimming.
ENGLISH
22
________________________________________
OPERATION
4 Make sure the person is seated
Function 2
so that their head is roughly at
your eye level. Before trimming, Beard trimming ...
comb the hair so that it falls
naturally and you can see the
direction in which it grows.
... using the beard trimming attach-
G
ment
(width 30 mm).
1 If necessary, remove the attach-
ment by pressing in both side
B
catches
and lifting off.
2 Insert beard trimming
G
attachment
carefully at the
top and press down until it clicks
into place.
3 Loosen the beard hair by comb-
ing the beard in the direction the
hair grows.
ENGLISH
23
________________________________________
OPERATION
Function 3
3 Push the extendable attachment
H
carefully and firmly onto the
Trimming hair or beards
at certain cutting
lengths ...
rounded rear half of the cutting
head from above and let it click
into place.
4 Adjust the cutting length (2, 4,
6, 8 or 10 mm) by pressing on
the lock next to the cutting
length display and then move
the comb to the setting you
want.
... using the extendable attachment
.
H
5 After use, remove extendable
H
attachment
by pressing the
locking tab at the back.
1 If necessary, remove the attach-
ment by pressing in both side
B
catches
and lifting off.
A
2 Insert attachment
(width
(width 30 mm)
G
38 mm) or
carefully at the top and press
down until it clicks into place.
ENGLISH
24
________________________________________
Note
OPERATION
Function 4
7
You can remove the single blade
foil of the shaving attachment. To
do this, press both side catches
on the shaving attachment. Clean
the blade head with the cleaning
brush supplied.
Close shaving ...
... using the shaving attachment
J
.
1 If necessary, remove the attach-
ment by pressing in both side
B
catches
and lifting off.
J
2 Insert shaving attachment
carefully at the top and press
down until it clicks into place.
Note
7
Do not apply a lot of pressure
when shaving, as this could
damage the single blade foil.
ENGLISH
25
________________________________________
OPERATION
I
Function 5
3 Push the thinning comb
care-
fully and firmly onto the rounded
rear half of the cutting head
from above and let it click into
place.
Thinning out hair ...
... using the thinning comb
(thinning at a length of 2 mm).
I
4 After use, remove thinning comb
I
by pressing the locking tab
at the back.
1 If necessary, remove the attach-
ment by pressing in both side
B
catches
and lifting off.
A
2 Insert attachment
(width
(width 30 mm)
G
38 mm) or
carefully at the top and press
down until it clicks into place.
ENGLISH
26
___________________________
CLEANING AND CARE
3 Use a soft, dry cloth or the brush
supplied to clean the appliance
housing and the charging unit.
Cleaning and care
1 Switch off the appliance and
unplug it from the mains.
Caution
2 Remove the attachment and
clean the blade head with the
brush supplied.
7
Never put the appliance, charging
unit or power supply unit in water
or any other liquid.
Caution
If cleaning with the brush is not
sufficient, you can also rinse the
attachment under running water.
However, only do this once the
4 Before using the appliance
again, dry all the attachments
properly using a soft towel.
7
5 Do not use any cleaning agents.
attachment has been removed.
Note
7
Remove any clippings after each
use.
7
The cutting head on the attachment
does not normally need to be
oiled. If you clean the attachment
under running water regularly but
you also want to maintain the
original condition of the cutting
head for as long as possible, it is
worth oiling it at regular intervals
with the oil provided.
ENGLISH
27
___________________________
Environmental note
CLEANING AND CARE
Storage
If you do not want to use the appli-
ance for a long period of time,
please store it carefully.
This product has been made from
high-quality parts and materials
which can be re-used and recycled.
1 Make sure it is unplugged, has
completely cooled down and all
the accessories are completely
dry.
Therefore, do not throw the product
away with normal household waste
at the end of its service life. Take it
to a collection point for recycling
electrical and electronic devices.
This is indicated by this symbol on
the product, in the operating
2 Store the parts in the original
box in a cool, dry place.
3 Make sure the appliance is kept
manual and on the packaging.
out of reach of children.
Please find out about collection
points operated by your local
authority.
Help protect the environment by
recycling used products.
ENGLISH
28
____________________________________
INFORMATION
Technical data
This product fulfils the
European directives
2004/108/EC and
2006/95/EC.
Power supply
Batteries: Nickel metal hydride
Power supply unit
Ni-MH
Technical and design modifications reserved.
ENGLISH
29
Grundig Multimedia B.V.
72011 903 8000
|