LCD TV RECEIVER
USER'S MANUAL
MODEL:
L1509A-A, L1709A-A, L1910A-A,
L2009A-A, L1911W-A
Please read this manual carefully before
using your television and keep this manual
In a good place for future reference.
Safety Notice Items
Incorrect usage will cause fire or electric shock. To prevent this, please do
as required when you are installing, using and cleaning this machine. To insure
your safety and extend the life-span of LCD-TV, please read the following items
carefully before using:
l Please read and understand all the instructions before operation;
l Please keep the book for later use;
l Please comply with the warning instructions on the machine and in this book
strictly;
l Please comply with the instructions provided;
l Please do not use additional devices that are not recommended by
manufacturer:
l Before operation, please make sure that the operating voltage of your unit is
normal;
l Do not placethe unit onunstable, dusty andhumid places;
l Never put theunit in directsunlight or nearheat sources;
l Allow enough space for proper ventilation;
l Please keep water away from the LCD-TV . If water comes in contact with the
LCD-TV, disconnect the power cord from the power source, then wipe the set
with a dry soft cloth;
l Do not remove the back cover. If services were need, please refer to qualified
Personnel
Front Panel Controls
L1509A-A, L1709A-A, L1910A-A,
L2009A-A
2
3
4
5
1
TV/AV MENU VOL- VOL+ CH-
CH+ POWER
L1911W-A
6
7
6
7
Control Panel Function
1. Power supply switch
2.TV/AV Select the input signals: COMPONENT/PC/AV/SV/TV
3. MENU Press to select the main menu
4. VOL- Volume down / Left orientation to adjust the item in the OSD
VOL+ Volume up / Right orientation to adjust the item/Press to enter
5. CH- TV channel down / to select the item in the menu
CH+ TV channel up / to select the item in the menu
6. Power indicator
Illuminates red in standby mode, illuminates green when the display is
turned on
7.Remote Sensor
Receiving remote control sends the infrared remote
signal.
Connection Options
The figure is just for reference, please see the real.
And the AC power supply switch is on the back of the set)
AV /S-VIDEO/COMPONENT Audio Input
Connect audio
output from an external
device to this jack
DVD/DTV Input
Connect a componentvideo/audio
device to thesejacks
Earphone port
Pb
Pr
Y
R
L
V
ANT IN
PC AUDIO IN
AUDIO IN
VIDEO IN
S-VIDEO
COMPONENT IN
VGA IN
PC Audio Input
S-Video Input
Connect S-Video out
from an S-Video device
to the jacks.
Connect the PC output
connector from a PC to
the audio input port
VGA Input
Video Input
Connect video
output from an external
device to this jack
Connect to the VGA
15PIN analog output
connector of the PC
display card for PC
display purpose
Antenna Input
Connect cable or
antenna signals to
the TV, either direc-
tly or through your
cable box.
Remote Control Key Functions
When using the remote control, aim it
Buttons on the remote control
towards the remotesensor on theTV
Stand By
MUTE
Display current input signal information
TV channel number select
Set time to change the TV into the
standby status after a period of preset
time.(time is 240/180/120/90/60/45/30/15/0)
NICAM/A2 Stereo select
SLEEP DISPLAY MUTE POWER
NICAM
PC
AUTO AD TV/AV
EXIT
Quick TV channel switch(return to the
last channel)
Volume down/up Left/right orientation to
adjust the item in the OSD
TV channel up/down or select the item
of the menu
PSM
OK
SSM
Select COMPONENT/PC/AV/SV/TV
Select picture mode
Q.VIEW
PC system select
P+
Select sound mode
Correspond to the differently colored
subjects
V-
V+
MENU
Switch to the Teletext with text mode/turn
off Teletext and switch to TV mode
Hold on or off for current page display
Switch to the Teletext with mix mode
Request index page
P-
INDEX
TEXT
SUBCODE MIX
Change display size
Sub coded page access
While in normal TV mode only, pressing
the button TIME will display the teletext
time in the top right corner for a few
seconds.
TIME
HOLD
SIZE
REVEAL
Reveal or hidden the hidden words
Press to select the main menu
Auto adjust (PC mode)
Remote Control
Installing Batteries
1.Slide open the cover of the battery compartment on the back of the remote
control.
2.Load two 5# alkaline batteries in the compartment. (plus and minus poles to
respective mark)
3.Replace the cover of the battery compartment.
1
2
3
Precautions
As strong light may interfere the
signals, change yourposition to
operate the remote controller if
the television cannot be turned
on or off as youexpect.
Make sure that there is no
obstacle between theremote
controller and televisionset.
Make sure that two 5# 1.5V alkaline
batteries are loaded. The batteries
must be of the same type. The batteries
must be located properly. The batteries
are not rechargeable.
Keep the remote controller
away from heat source or
humid area toensure
effective performance of
the remote controller.
Connection Instructions
Grounding
Ensure that you connect the grounding / earth wire to prevent possible
electric shock. If grounding methods are not possible, have a qualified
electrician install a separate circuit breaker. Do not try to ground the
unit by connectingit to telephone wires, lighteningrods, or gaspipes.
External Equipment Connections
Antenna Connection
- Antenna or Cable Service with a Cable Box Connections
- For optimum picture quality, adjust antenna direction if needed.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
wall antenna
socket
ANT IN
RF coaxial wire (75 ohm)
VHF antenna
UHF antenna
Be careful not to bend the bronze
wire when connecting the antenna.
outdoor
antenna
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
To improve picture quality in a poor
signal area, purchase and install a
signal amplifier.
ANT IN
If the antenna needs to be split for two
TV s, install a 2-Way Signal Splitter
in the connections.
If the antenna is not installed properly,
contact your dealer for assistance.
NOTE: All cables shown are not included with the TV
Connection Instructions
PC Setup
You can use your LCD-TV as a monitor for your personal computer using a VGA
cable (not supplied).
Connection and use steps:
1.Read the userguide supplied with
your computer and ensure that it has
a VGAconnector;
2.Make sure that the power of the LCD
-TV and thePC are off;
VGA IN
3.Connect a Dtype 15-pin VGAinterface
cable ( not supplied ) to the VGAvideo
interface connector on the PC. Then
connect the other end to the VGA video
interface connector on the back of the
LCD-TV.Tighten the screwson the VGA
connectors once they are firmly
connected;
4.Turn on the power ofthe LCD-TV first,
and then turn on the power of the PC;
5.Press the TV/AV button to set the video
input mode ofthe LCD-TV toPC-RGB;
6.Check the image on your TV. There may be noise associated with the resolution,
vertical pattern, contrast or brightness in PC mode. If noise is present, change
the PC mode to another resolution, change the refresh rate to another rate or
adjust the brightness and contrast on the menu until the picture is clear. If the
refresh rate of the PC graphic card can not be changed,change the PC graphic
card or consult the manufacturer of the PC graphic card.
Connection Instructions
VCR Setup
- To avoid picture noise (interference), leave an adequate distance between the
VCR and TV
Connection and use steps:
1.Read the user guide supplied with your AV devices and ensure that it has
Composite or S-Video connectors;
2.Make sure that the power of the LCD-TV and the AV device are off;
Connection Option 1
Set VCR output switch to 3 or 4 and then
tune TV to the same channel number.
Connection Option 2
1. Connect the audio and video cables from
the VCR's output jacks to the TV input jacks,
as shown in the figure.
When connecting the TV to VCR, match
2
the jack colors (Video = yellow,Audio
Left = white,and Audio Right = red).
If you connect an S-VIDEO output from
VCR to the S-VIDEO input, the picture
1
quality is improved; compared to conne-
.
cting a regular VCR to the Video input.
2. Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner
manual.)
s
VCR
3.Turn on the power of the LCD-TV first ;
and then turn on the power of the AV
device;
4.Press the TV/AV button to set the video
input mode of the LCD-TV to S-VIDEO
mode or AV mode.
Connection Instructions
Cable TV Setup
- After subscribing to a cable TV service from a local provider you can watch cable
TV programming. The TV cannot display TV programming unless a TV tuner
device or cableTV converter box is connectedto the TV.
- For furtherinformation regarding cableTV service, contact your localcable TV
service provider(s).
Connection Option 1
1. Select 3or 4 withchannel switch oncable
box.
2. Tunethe TV channel to thesame selected
output channel oncable box.
3. Select channelsat the cablebox or with
the cable boxremote control.
Connection Option 2
1. Connect theaudio and videocables from
the Cable Box'soutput jacks tothe TV
input jacks, asshown in thefigure.When
connecting the TV to aCable Box, match
the jack colors
(Video = yellow, Audio Left =white, and
Audio Right= red).
2. Select theinput source byusing the TV/AV
button on theremote control.
3. Select yourdesired channel withthe
remote control forcable box.
External AV Source Setup
How to connect
Connect the audioand video cablesfrom
the external equipment'soutput jacks tothe
TV input jacks, as shown inthe figure.
When connecting theTV to external equip-
ment, match thejack colors (Video = yellow,
Audio Left =white, andAudio Right =red).
How to use
1. Select theinput source byusing the TV/AV
button on theremote control.
2. Operate thecorresponding external equi-
pment. Refer toexternal equipment ope-
rating guide.
Basic Operating Instructions
Turn on the LCD-TV
SLEEP DISPLAY MUTE POWER
Switch on the power button on the back of the set and the TV
will in standby mode. When the POWER button on the remote
control is pressed and the LCD-TV is turned on, the indicator
light on the front of the LCD-TV changes from red to green.
When the LCD-TV is turned off using the POWER button, the
LCD-TVwill go into standby mode and the indicator light turns
red.
NICAM
PC
AUTO AD TV/AV
PSM
OK
.SSM
Q.VIEW
P+
TV
V-
MENU
V+
Note:
The display of the input mode
will disappear in 3 seconds.
P-
INDEX
TEXT
COMPONENT
PC
SUBCODE MIX
TIME
HOLD
SIZE
REVEAL
AV
SV
Switch Among Different Inputs: TV / COMPONENT / PC / AV / SV
Each time you press the TV/AV button, TV, COMPONENT , PC, AV, SV,
will appear on the screen in the order.
.Note:
The display of the input mode will disappear in 3 seconds.
Audio Control
1.Press the V+ button to increase the volume. A number will appear on
screen indicating the volume level.
2.Press the V- button to decrease the volume. A number will appear on
screen indicating the volume level.
Mute
1.Press the MUTE button to mute the sound temporarily. A mute icon
appears on the screen.
2.Press the MUTE button or V+/V- again to restore the sound.
The mute icon disappears.
Basic Operating Instructions
Select the TV Channel You Want
You can use the number keys on the remote control to directly select TV
channels.
The LCD-TV can store up to 100 channels , and you can press the keys on the
remote control or on the panel to make a selection.
1.Press the relevant key on the remote control if you want to choose any channel
from 0 to 9. for example: if you want to choose channel 8, just press the key
number 0 and 8.
Note: You must press 0 first and then the other numbers from 0 to 9 if you want
To choose channels from 0 to 9)
2.If you want to choose a channel bigger than 9, please enter the two digits of the
channel number you want to watch within 3 seconds. for example: select
channel 16
Picture Mode
Press PSM button on the remote control for menu display . For desired mode as
follows:
PERSONAL STANDARD MILD FRESH
Menu Operations
* In this manual, the OSD (On Screen Display) may be different from your TV
because it is just an example to help you with the TV operation.
s
Press TV/AV to select the input source, and the menu in the different source is
different .
1. Press MENU button to display the main menu, and V+/V-to select the
main menu .
2. Press P+/P- to scroll through the parameters
3. Press V+/V- buttons to make changes to the parameters
4. Press the OK button to exit the menu
Picture Menu Options
Picture quality can be adjusted for any input separately .
The picture qualityon the screencan be adjustedas follows:
1. Press MENU button and V+/V- until the followingmenu appears
on the screen.
PC/COMPONENT MENU
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
COLOR TEMP.
30
30
2
COLD
30
TV/AV/SV MENU
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
SATURATION
HUE
50
50
2
50
50
Only available inNTSC system
Note: Sign ontop of themenu in thismanual may bedifferent from the real
Menu Operations
Picture Menu Options continued
2. Press P+/P- button to enter the picture menu and to go up and down to
select the desired option .
3.Press V+/V- button to increase and decrease the level to adjust the
selected option to your preference .
4. Repeat step 2 and step 3 until desired picture quality has been achieved .
Function:
BRIGHTNESS :Adjust the brightness of the picture . By increasing the level, it
will add more light to dark parts of the picture and by decreasing the level ,it will
add more dark to light parts of the picture.
CONTRAST : Adjust the contrast of the picture . The image becomes higher as
the number increase.
SHARPNESS : Adjust the amount of the detail enhancement , the image
sharpness rises as the number increases (By increasing the level, it will show
cleaner and clearer images and by decreasing the level, it will make picture
smoother).
SATURATION : Press V+/V- to adjust the color
HUE : Adjust the tone of the picture . Appear and be adjusted only under NTSC
mode
COLOR TEMP. : Press to select the color temperature from WARM/NORMAL/
COLD .
Audio Menu Options
Sound can be adjusted for any input as follows:
1. Press MENU and V+/V- button until the following menu appears on
the screen
AUDIO
50
50
50
50
VOLUME
BALANCE
BASS
TREBLE
AUDIO MODE
AVL
VOICE
OFF
Menu Operations
Audio Menu Options continued
You can adjust sound options to the levels you prefer.
2. Press P+/P- button to enterthe audio menuand to goup and downto
select the desired option .
3.Press V+/V- button to increase and decrease the level to adjust the
selected option toyour preference .
4. Repeat step2 and step3 until desiredsound quality hasbeen achieved ..
Function :
VOLUME :Adjust the volumeof your TV
BALANCE : Adjust the balance of the audio output from left to right . When
indication value of balance increases toward +50 , sound of the left speaker
becomes weaker . When indication value of balance decreases toward -50 ,
sound of the right speaker become weaker .
BASS : Adjust the bass of the sound . Can only be adjust under PERSONAL mode .
TREBLE : Adjust thetreble of thesound . Canonly be adjustunder PERSONAL
mode .
AUDIO MODE : Press V+/V- to select among PERSONAL, VOICE, MUSIC and
THEATRE .
AVL: Automatic Volume Limit Control reduces the effect of the large volume by
the same volume of all the channels .
Menu Operations
Function Menu Options
Menu Language Selection:
The menus can be shown on the screen in the selected language. First select
your language.
1. Press MENU and V+/V- button until the following menu appears on the screen
2. Press P+/P- button to select LANGUAGE.
3. Press V+/V- button to select your desired language.
From this point on, the on-screen menus will be shown in the language of your
choice.
FUNCTION
INPUT SOURCE
LANGUAGE
TXT LANGUAGE
TXT EAST/WEST
BLUE SCREEN
RESET
TV
ENGLISH
PAN EUROPEAN
EAST
ON
1. Press MENU button and V+/V- until the following menu appears
on the screen.
FUNCTION
INPUT SOURCE
LANGUAGE
TXT LANGUAGE
TXT EAST/WEST
BLUE SCREEN
RESET
TV
ENGLISH
PAN EUROPEAN
EAST
ON
2. Press P+/P- button to enter the function menu and to go up and down to
select the desired option .
3.Press V+/V- button to increase and decrease the level to adjust the
selected option to your preference .
4. Repeat step 2 and step 3 until desired picture quality has been achieved .
Functions:
1. INPUT SOURCE : Display current mode . There are PC , AV , SV ,TV,
COMPONENT to display .
Menu Operations
Function Menu Options Continued
2. TXT LANGUAGE: To switch the teletext languages.
3. TXT EAST/WEST: To select EASTor WEST .
4.BLUE SCREEN:To set On, the screen will be in blue screen after 3 seconds
if there is no signal.
5. RESET : Press V+ to reset some settings to the factory default .
Adjust Menu Options
1. Press MENU and V+/V- button until the following menu appears on the
screen
ADJUST
AUTO SYNC.
PHASE
CLOCK
H POSITION
V POSITION
50
50
50
50
Note: This menu is only appears in PC mode .
2. Press P+/P- button to enter the adjust menu and to go up and down to
select the desired option .
3.Press V+/V- button to increase and decrease the level to adjust the
selected option to your preference .
4. Repeat step 2 and step 3 until desired quality has been achieved ..
Functions:
AUTO SYNC : Is opted for adjustment of picture location frequency and phase
parameters .
PHASE : Removes any horizontal distortion and clears or sharpness the displayed
characters .
CLOCK : Adjust the TFT-LCD to match the PC input source
H-POSITION : Picture horizontal adjust
V-POSITION : Picture vertical position adjust .
Menu Operations
Tuning Menu Options
1. Press MENU and V+/V- button until the following menu appears on the
screen
TUNING
CHANNEL
1
AUTO
DK
OFF
ON
COLOR SYSTEM
SOUND SYSTEM
SKIP
AFC
FINE TUNE
EXCHANGE
MANUAL SEARCH
AUTO SEARCH
Note: This menuis only appearsin TV mode.
2. Press P+/P- button to enter the tuning menu and to go up and down to
select the desired option .
3.Press V+/V- button to increase and decrease the level to adjust the
selected option to your preference .
4. Repeat step 2 and step 3 until desired quality has been achieved ..
Functions:
1. CHANNEL : Press V+/V- to change the TV channel .
2.COLOR SYSTEM : Select the TV color system from AUTO,PAL,SECAM.
3.SOUND SYSTEM : Select the TV standard system from DK,I,L/L',BG
4. SKIP : If you want skip a channel , press V+/V- to select ON , and this
channel will be skip next time when you press P+/P- . But you can press
digits button to select the channel . If you want to restore the channel , select
OFF.
5. AFC : Auto frequence control . Select ON to improve the image quality .
6. FINE TUNE : If the image received is not very good , you can press P+/P-
to select FINE TUNE item in menu . Then , press V+/V- button to adjust
and improve the image quality .
Menu Operations
Tuning Menu Options Continued
7. EXCHANGE : Press V+ to display the menu as follows:
EXCHANGE
FROM :
TO :
1
9
EXCHANGE
Press P+/- to select the item and then V+/- to adjust the channel and V+
to confirm.( For example: press P+/- to select FROM item, and then press
V+/- to adjust the channel number to 1; then Press P+/- to select TO item,
and V+/- to adjust the channel number to 9; press P+/- to select EXCHANGE item,
and then V+ to confirm. The two channels will be exchanged)
8. MANUAL SEARCH : Press V+/V- to start to search the channel .
9. AUTO SEARCH : Auto search and save the channel .Press the V+ button to
ensure automatic search function operates. All channels now playing program
will be automatically preset in order .After the search has finished, the first
program number will display on the screen.
NOTE: If you want to search the channels in L or L' system, you need to set the sound
system to L in OSD
TELETEXT
Some menu related function are not available in TELETEXT mode. MENU and AUTO AD
control functions are not available in TELETEXT mode. If the TV is switched on by POWER
after off in TELETEXT mode, or press TV/AV or PC button, the TELETEXT mode will
disappear automatically.
Teletext features may vary depending on the Broadcasting
Companies and is only available if the channel selected is
SLEEP DISPLAY MUTE POWER
NICAM
PC
AUTO AD TV/AV
transmitting Teletext. Pressing the TEXT button whilst in
Teletext operation will switch the current status to TV.
When in Teletext mode, the volume may still be altered to
the desired listening level.
PSM
OK
.SSM
Q.VIEW
P+
V-
MENU
V+
Page Selection
P-
INDEX
TEXT
Pages can beselected in twoways:
a. Press P+ or P- button to increase or decrease the
page number by one.
SUBCODE MIX
TIME
HOLD
SIZE
REVEAL
b. By entering the page number, using the number
keys on the remote control.
SIZE Button
Press SIZE button to change display size : normal large top large bottom
normal
REVEAL Button
Press REVEAL to reveal hidden words e.g. Quiz page answers . Press again
to hide.
Red/Green/ Yellow/CyanButtons
These four buttons correspond to the differently colored subjects .
HOLD Button
Press HOLD button to remain the Teletext page when viewing multi-page
information .
INDEX Button
Press INDEX button to return to the main index page .
Depending on the way information is transmitted , this may have to be pressed
more than once to return to the main index page .
TELETEXT
SUBCODE Button
When Teletext information exceeds more than one page , it may take some time
for the automatic changing of the sub pages to reach the sub page you require .
It is possible to enter your required sub page and continue watching the normal
programme until the correct sub page is found .
Select the required page number using buttons 0-9 .
If the top of the page indicates that sub pages are being transmitted yet the page
does not change . Then the number at the top of the page is there to indicated
that the broadcaster has updated the page s contents , there are no sub pages .
Press SUBCODE button , page number/--- will be displayed at the bottom right
of the screen.
Enter desired sub page number before the page number/--- disappears . To
select page 6 enter 0,0,0 and 6 .
TEXT Button
Press TEXT to enter Teletext mode and only the text page can be visible .
MIX Button
Press MIX button to enter Teletext mode and both the TV picture and text page
can be visible.
TIME
While in normal TV mode only, pressing the button TIME will display the
teletext time in the top right corner for a few seconds.
Troubleshooting Guide
To assist in location possible faults use help guide below.
Troubleshooting
Verify ifthe television isproperly plugged.
Verify ifthe television isproperly supplied power.
Verify ifelectricity is available.
No picture, no sound
Verify if correct signals are input.
Press TV/AV button to change signal input to TV input.
Restart the television of power supply is interrupted.
Blank screen
Press MUTE button and verify if Mute mode is set.
Switch to other channel and verify if the same problem
happens.
No sound
Press VOL+ button to see if the problem can be solved.
Verify ifsound system iscorrect. Refer tosome chapter
for adjust.
Poor sound
Verify ifcorrect channel isselected.
Adjust the antenna.
Make adjustments byFINE TUNE and MANUAL SEARCH.
No picture in some
channel
Verify if the same problem exists in other channels.
Check out of picture and sound systems.
Refer to relative instructions in the Manual for color
adjust.
No color for some channel
program (black and white)
Verify ifthe antenna iscorrectly connected.
Verify ifthe antenna isin good condition.
Make fine adjustmentof channel.
Spots with some or
all pictures
Disconnect the televisionfrom power supplyand, 10
seconds later, connect the televisionto the powersupply.
If the problemstill exists, contactauthorized after-sales
service for technicalassistance.
Television out of control
Note:
1.If the fault can not be repaired using the above guide consult with your local authorized service
center.
2.The TV set must only be repaired by a qualified registered service person. Never attempt to
remove the back cover as the TV set has dangerous voltages in side that may cause a fatally or fire.
Specifications
Specifications of the television that you have just purchased may
vary from the information in this table due to technical innovations.
Model
L1509A-A/L1709A-A L1910A-A/L2009A-A/L1911W-A
Picture, sound
PAL/SECAM-B/G,I,D/K,L,L
system
Audio output
External port
1.5W+1.5W
AV input PC input S-VIDEO input PC audio input
Headphone output COMPONENT input Antenna input
~150-240V 50/60Hz
Power requirements
Power consumption
Temperature
50W
60W
Working:5 C~35 C
Storage:-10 C~45 C
Remote control
Batteries
Accessories
Owner's manual
Warranty card
Note Warranty card is only forthe special countriesand areas
Note:
All specifications are subject to change without notice.
All quality are approximate value.
V0.1
0090508262
|