LCD TV RECEIVER
USER'S MANUAL
MODEL:
WL19T1, WL22T1
Please read this manual carefully before
using your television and keep this manual
In a good place for future reference.
Safety Notice Items
Incorrect usage will cause fire or electric shock. To prevent this, please do
as required when you are installing, using and cleaning this machine. To insure
your safety and extend the life-span of LCD-TV, please read the following items
carefully before using:
Please read andunderstand all theinstructions before operation;
Please keep the book for later use;
Please comply with the warning instructions on the machine and in this book
strictly;
Please comply with the instructions provided;
Please do not use additional devices that are not recommended by
manufacturer:
Before operation, please make sure that the operating voltage of your unit is
normal;
Do not placethe unit onunstable, dusty andhumid places;
Never put theunit in directsunlight or nearheat sources;
Allow enough space for proper ventilation;
Please keep water away from the LCD-TV . If water comes in contact with the
LCD-TV, disconnect the power cord from the power source, then wipe the set
with a dry soft cloth;
Do not remove the back cover. If services were need, please refer to qualified
Personnel
Front Panel Controls
T1
Control Panel Function
1. Power supply switch
2.TV/AV
Select the input signals: TV/AV/S-VIDEO/PC/COMPONENT
3. MENU Press to select the main menu
4. VOL- Volume down / Left orientation to adjust the item in the OSD
VOL+ Volume up / Right orientation to adjust the item/Press to enter
5. CH- TV channel down / to select the item in the menu
CH+ TV channel up / to select the item in the menu
6. Power indicator
Illuminates red in standby mode, illuminates green when the display is
turned on
7.Remote Sensor
Receiving remote control sends the infrared remote
signal.
Connection Options
The figure is just for reference, please see the real.)
AV /S-VIDEO/COMPONENT Audio Input
Connect audio
output from an external
device to this jack
COMPONENTInput
Connect a componentvideo/audio
device to thesejacks
Earphone port
Pb
Pr
Y
R
L
V
VGA IN
ANT IN
PC AUDIO IN
VIDEO IN
S-VIDEO
COMPONENT IN
AUDIO IN
PC Audio Input
S-Video Input
Connect S-Video out
from an S-Video device
to the jacks.
Connect the PC output
connector from a PC to
the audio input port
VGA Input
Video Input
Connect video
output from an external
device to this jack
Connect to the VGA
15PIN analog output
connector of the PC
display card for PC
display purpose
Antenna Input
Remote Control Key Functions
When using the remote control, aim it
Buttons on the remote control
towards the remotesensor on theTV
Stand By
MUTE
Display current input signal information
TV channel number select
Set time to change the TV into the
standby status after a period of preset
time.
SLEEP DISPLAY MUTE POWER
NICAM
PC
AUTO AD TV/AV
NICAM/A2 Stereo select
EXIT
Quick TV channel switch(return to the
last channel)
Volume down/up Left/right orientation to
adjust the item in the OSD
TV channel up/down or select the item
of the menu
PSM
OK
SSM
Select TV/AV/S-VIDEO/PC/
COMPONENT
Q.VIEW
Select picture mode
P+
PC system select
Select sound mode
Correspond to the differently colored
subjects
V-
V+
MENU
Switch to the Teletext with text mode/turn
off Teletext and switch to TV mode
Hold on or off for current page display
Switch to the Teletext with mix mode
Request index page
P-
INDEX
TEXT
SUBCODE MIX
Change display size
Sub coded page access
While in normal TV mode only, pressing
the button TIME will display the teletext
time in the top right corner for a few
seconds.(only available in teletext mode)
Reveal or hidden the hidden words
Press to select the main menu
Auto adjust (PC mode)
TIME
HOLD
SIZE
REVEAL
Remote Control
Installing Batteries
1.Slide open the cover of the battery compartment on the back of the remote
control.
2.Load two 5# alkaline batteries in the compartment. (plus and minus poles to
respective mark)
3.Replace the cover of the battery compartment.
1
2
3
Precautions
As strong light may interfere the
signals, change yourposition to
operate the remote controller if
the television cannot be turned
on or off as youexpect.
Make sure that there is no
obstacle between theremote
controller and televisionset.
Make sure that two 5# 1.5V alkaline
batteries are loaded. The batteries
must be of the same type. The batteries
must be located properly. The batteries
are not rechargeable.
Keep the remote controller
away from heat source or
humid area toensure
effective performance of
the remote controller.
Connection Instructions
Grounding
Ensure that you connect the grounding / earth wire to prevent possible
electric shock. If grounding methods are not possible, have a qualified
electrician install a separate circuit breaker. Do not try to ground the
unit by connectingit to telephone wires, lighteningrods, or gaspipes.
External Equipment Connections
Antenna Connection
- Antenna or Cable Service with a Cable Box Connections
- For optimum picture quality, adjust antenna direction if needed.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
wall antenna
socket
ANT IN
RF coaxial wire (75 ohm)
VHF antenna
UHF antenna
Be careful not to bend the bronze
wire when connecting the antenna.
outdoor
antenna
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
To improve picture quality in a poor
signal area, purchase and install a
signal amplifier.
ANT IN
If the antenna needs to be split for two
TV s, install a 2-Way Signal Splitter
in the connections.
If the antenna is not installed properly,
contact your dealer for assistance.
Note:All cables shownare just forexample.
Connection Instructions
VGA Input
You can use your LCD-TV as a monitor for your personal computer using a VGA
cable (not supplied).
Connection and use steps:
1.Read the userguide supplied with
your computer and ensure that it has
a VGAconnector;
2.Make sure that the power of the LCD
-TV and thePC are off;
VGA IN
3.Connect a Dtype 15-pin VGAinterface
cable ( not supplied ) to the VGAvideo
interface connector on the PC. Then
connect the other end to the PC video
interface connector on the back of the
LCD-TV.Tighten the screwson the VGA
connectors once they are firmly
connected;
4.Turn on the power ofthe LCD-TV first ,
and then turn on the power of the PC;
5.Press the TV/AV button to set the video
input mode of the LCD-TV to PC;
6.Check the imageon your TV. There may be noise associatedwith the resolution,
vertical pattern, contrast or brightness in PCmode. If noise is present, change
the PC modeto another resolution, change the refreshrate to anotherrate or
adjust the brightnessand contrast onthe menu untilthe picture isclear. Ifthe
refresh rate of the PC graphic card can not be changed, change the PC graphic
card or consult the manufacturer of the PC graphic card.
Resolution
Mode
VGA
Resolution
640*480
Line frequency (Khz) Frame frequency (Hz)
31.5KHz
37.9KHz
48.4KHz
60Hz
60Hz
60Hz
SVGA
XGA
800*600
1024*768
Note: Allabove listed aresubject to VESACriteria.
YPbPr Input
How to connect
Connect the DVD video outputs (Y, PB, PR)
to the COMPONENT(Y, Pb, Pr) IN jacks on
the TV and connect theDVD audio outputs
to the AUDIO IN jacks on the TV, as shown
in the figure.
NOTE: If your DVD player doesnot have
component video output,use S-Video.
How to use
1. Turn on the DVD player, insert a DVD.
2. Use the TV/AV button on theremote control toselect
Connection Instructions
COMPONENT (If connected to SVIDEO,select the SV external
input source.)
3. Refer to the DVD player's manual for operating instructions.
Component Input ports
To get better picture quality, connect a DVD player to the component
input ports as shown below.
Y
Pb
Pr
S-VIDEO Input
- To avoid picture noise (interference), leave an adequate distance between the
VCR and TV
Connection and use steps:
1.Read the user guide supplied with your AV devices and ensure that it has
S-Video connectors;
2.Make sure that the power of the LCD-TV and the AV device are off;
Connection Option 1
Set VCR output switch to 3 or 4 and then
tune TV to the same channel number.
Connection Option 2
1. Connect the audio and Svideo cables
from the VCR's output jacks to the TV
input jacks, as shown in the figure.
2. Insert a video tape into the VCR and
press PLAY on the VCR. (Refer to the
VCR owner s manual.)
2
3.Turn on the power of the LCD-TV first ;
and then turn on the power of the AV
device;
1
4.Press the TV/AV button to set the video
input mode of the LCD-TV to S-VIDEO
mode .
VCR
Connection Instructions
Cable TV Input
- After subscribing to a cable TV service from a local provider you can watch cable
TV programming. The TV cannot display TV programming unless a TV tuner
device or cableTV converter box is connectedto the TV.
- For furtherinformation regarding cableTV service, contact your localcable TV
service provider(s).
Connection Option 1
1. Select 3 or 4 with channel switch on cable
box.
2. Tune the TV channel to the same selected
output channel oncable box.
3. Select channelsat the cablebox or with
the cable box remote control.
Connection Option 2
1. Connect the audio and video cables from
the Cable Box'soutput jacks tothe TV
input jacks, as shown in the figure.When
connecting the TV to a Cable Box, match
the jack colors
(Video = yellow, Audio Left = white, and
Audio Right= red).
2. Select the input source by using the TV/AV
button on the remote control.
3. Select your desired channel with the
remote control forcable box.
External AV Source Input
How to connect
Connect the audio and video cables from
the external equipment's output jacks to the
TV input jacks, as shown in the figure.
When connecting the TV to external equip-
ment, match the jack colors (Video = yellow,
Audio Left =white, andAudio Right =red).
How to use
1. Select the input source by using the TV/AV
button on the remote control.
2. Operate the corresponding external equi-
pment. Refer to external equipment ope-
rating guide.
Basic Operating Instructions
Turn on the LCD-TV
SLEEP DISPLAY MUTE POWER
When the POWER button on the remote control is pressed
and the LCD-TV is turned on, the indicator light on the front of
the LCD-TV changesfrom red togreen. When theLCD-TV is
turned off using the POWERbutton, the LCD-TVwillgo into
standby mode and the indicator light turns red.
NICAM
PC
AUTO AD TV/AV
PSM
OK
.SSM
Q.VIEW
Note:
The display of the input mode will disappear in about 8
seconds.
P+
V-
MENU
V+
P-
INDEX
TEXT
SUBCODE MIX
You can also turn on the TV from standby mode by pressing
the digits(1-9) orP+/- .
TIME
HOLD
SIZE
REVEAL
Switch AmongDifferent Inputs: TV/AV/S-VIDEO/PC/COMPONENT
Each time you press the TV/AV button, TV/AV/S-VIDEO/PC/COMPONENT will
appear on the screen .
The display will appear on the screen when the TV is turned on the first time:
(Different displays for different countries, please see the real set)
AUTO SEARCH
AUTO SEARCH
or
UNITED KINGDOM
NO
OTHER
YES
NO
YES
Press V+/- to adjust among countries list on the screen just according to the
country you are in, P+/- to select the option and MENU to confirm.
Audio Control
1.Press the V+ button to increase the volume. A number will appear on
screen indicating the volume level.
2.Press the V- button to decrease the volume. A number will appear on
screen indicating the volume level.
Mute
1.Press the MUTE button to mute the sound temporarily. A mute icon
appears on the screen.
2.Press the MUTE button again or V+/V- to restore the sound.
The mute icon disappears.
Basic Operating Instructions
Select the TV Channel You Want
You can use the number keys on the remote control to directly select TV
channels.
The LCD-TV can store up to 100 channels , and you can press the keys on the
remote control or on the panel to make a selection.
1.Press the relevant key on the remote control if you want to choose any channel
from 0 to 9. for example: if you want to choose channel 8, just press the key
number 0 and 8.
Note: You must press 0 first and then the other numbers from 0 to 9 if you want
To choose channels from 0 to 9)
2.If you want to choose a channel bigger than 9, please enter the two digits of the
channel number you want to watch within 3 seconds. for example: select
channel 16
Picture Mode
Press PSM button on the remote control for menu display . For desired mode as
follows:
PERSONAL STANDARD MILD FRESH
Menu Operations
* In this manual, the OSD (On Screen Display) may be different from your TV
because it is just an example to help you with the TV operation.
s
Press TV/AV to select the input source, and the menu in the different source is
different .
1. Press MENU button to display the main menu, and V+/V-to select the
main menu .
2. Press P+/P- to scroll through the options
3. Press V+/V- buttons to make changes to the parameters
4. Press the OK button to exit the menu
Picture Menu Options
Picture quality can be adjusted for any input separately .
The picture qualityon the screencan be adjustedas follows:
1. Press MENU button and V+/V- until the followingmenu appears
on the screen.
2. Press P+/P- button to enterthe picture menuand to goup and downto
select the desired option .
PC MENU
COMPONENT MENU
PICTURE
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
COLOUR TEMP.
30
30
2
BRIGHTNESS
CONTRAST
SHARPNESS
COLOUR
30
30
2
COLD
30
0
0
H.POSITION
V.POSITION
30
30
TV/AV/S-VIDEO MENU
PICTURE
BRIGHTNESS
CONTRAST
SHARPNESS
COLOUR
50
50
2
50
OFF
50
NOISE REDUCTION
HUE
Only available inNTSC system
Note: Sign ontop of themenu in thismanual may bedifferent from the real
Menu Operations
Picture Menu Options continued
3.Press V+/V- button to increase and decrease the level to adjust the
selected option to your preference .
4. Repeat step 2 and step 3 until desired picture quality has been achieved .
Function:
BRIGHTNESS :Adjust the brightness of the picture . By increasing the level, it
will add more light to dark parts of the picture and by decreasing the level ,it will
add more dark to light parts of the picture.
CONTRAST : Adjust the contrast of the picture . The image becomes higher as
the number increase.
SHARPNESS : Adjust the amount of the detail enhancement , the image
sharpness rises as the number increases (By increasing the level, it will show
cleaner and clearer images and by decreasing the level, it will make picture
smoother).
COLOUR : Press V+/V- to adjust the colour
NOISE REDUCTION: Adjust the quality of the picture by selecting OFF,LOW,
MID,HIGH.
HUE : Adjust the tone of the picture . Appear and be adjusted only under NTSC
mode
COLOUR TEMP. : Press to select the colour temperature from WARM/NORMAL/
COLD .
H.POSITION : Picture horizontal adjust
V.POSITION : Picture vertical position adjust .
Audio Menu Options
Sound can be adjusted for any input as follows:
1. Press MENU and V+/V- button until the following menu appears on
the screen
AUDIO
50
50
50
50
VOLUME
BALANCE
BASS
TREBLE
AUDIO MODE
AVL
VOICE
OFF
Menu Operations
Audio Menu Options continued
You can adjust sound options to the levels you prefer.
2. Press P+/P- button to enterthe audio menuand to goup and downto
select the desired option .
3.Press V+/V- button to increase and decrease the level to adjust the
selected option toyour preference .
4. Repeat step2 and step3 until desiredsound quality hasbeen achieved ..
Function :
VOLUME :Adjust the volumeof your TV
BALANCE : Adjust the balanceof the audiooutput from leftto right . When
indication value of balance increases toward 100 , sound of the left speaker
becomes weaker . When indication value of balance decreases toward 0,
sound of the right speaker become weaker .
BASS : Adjust the bass of the sound . Can only be adjust under PERSONAL mode .
TREBLE : Adjust thetreble of thesound . Canonly be adjustunder PERSONAL
mode .
AUDIO MODE : Press V+/V- to select among PERSONAL, VOICE, MUSIC and
THEATRE .
AVL: Automatic Volume Limit Control reduces the effect of the large volume by
the same volume of all the channels .
Menu Operations
Function Menu Options
1. Press MENU button and V+/V- until the following menu appears
on the screen.
FUNCTION
INPUT SOURCE
LANGUAGE
TV
ENGLISH
PAN EUROPEAN
EAST
TXT LANGUAGE
TXT EAST/WEST
BLUE SCREEN
DISPLAY MODE
RESET
ON
4:3
CHILD LOCK
2. Press P+/P- button to enterthe function menu and to go up and down to
select the desired option .
3.Press V+/V- button to increase and decrease the level to adjust the
selected option to your preference .
4. Repeat step 2 and step 3 until desired picture quality has been achieved .
Functions:
1. INPUT SOURCE : Display current mode . There are TV/AV/S-VIDEO/PC/
COMPONENT to display .
2. LANGUAGE: This item displays the language of the OSD.
3. TXT LANGUAGE: To switch the teletext languages.
4. TXT EAST/WEST: To select EASTor WEST.
5.DISPLAY MODE: To select the display mode :4:3/16:9/FULLSCREEN.
6.BLUE SCREEN :To set On, the screen will be in blue screen after 3 seconds
if there is no signal.
7. RESET : Press V+ to reset somesettings to thefactory default .
8. CHILD LOCK:Press V+ to enter it and input the password correctly, the
CHILD LOCK menu will appear on the screen.
PASSWORD: The password can be changed. Press P+/- to select PASSWORD
and V+ to enter. The screen will display NEW PW:----,then enter the new
password and the screen display CONFIRM PW:----, if the same password is
input correctly twice, the old password will be changed.
CHILD LOCK: Press P+/- to select it . Press V+/- to set on or off mode. If lock
on mode is set, child lock is inactivated automatically. In such case, buttons
on the television is useless and only buttons on remote control can be used,
Menu Operations
if buttons onthe television arepressed, the screenwill display CHILDLOCK.
The child lockmode can beresumed by enteringlock set menu, set child lock
on.
Adjust Menu Options
1. Press MENU and V+/V- button until the following menu appears on the
screen
ADJUST
AUTO SYNC.
PHASE
CLOCK
H. POSITION
V. POSITION
50
50
50
50
Note: This menu only appears in PC mode .
2. Press P+/P- button to enter the adjust menu and to go up and down to
select the desired option
3.Press V+/V- button to increase and decrease the level to adjust the
selected option to your preference ..
4. Repeat step 2 and step 3 until desired quality has been achieved .
Functions:
AUTO SYNC : Is opted for adjustment of picture location frequency and phase
parameters .
PHASE : Removes any horizontal distortion and clears or sharpness the displayed
characters .
CLOCK : Adjust theTFT-LCD to match the PC inputsource
H.POSITION : Picture horizontal adjust
V.POSITION : Picture vertical position adjust.
Menu Operations
Tuning Menu Options
1. Press MENU and V+/V- button until the following menu appears on the
screen
TUNING
TUNING PROGRAM
AUTO SEARCH
Note: This menuonly appears inTV mode .
2. Press P+/P- button to enterthe tuning menu and to go up and down to
select the desired option .
3.Press V+/V- button to increase and decrease the level to adjust the
selected option to your preference .
4. Repeat step 2 and step 3 until desired quality has been achieved ..
Functions:
1.TUNING PROGRAM: Press V+ to enter it and the TUNING PROGRAM menu
appears:
TUNING PROGRAM
CHANNEL
1
EDIT NAME
COLOUR SYSTEM
SOUND SYSTEM
SKIP
AUTO
DK
OFF
ON
AFC
FINE TUNE
EXCHANGE
MANUAL SEARCH
143.65MHZ
CHANNEL : Press V+/V- to change the TV channel .
EDIT NAME: Press V+ to enter it , then press V+/- to select the position you want to
edit and press P+/- to input the emblem such as character and so on.(There are 8
position for you to edit totally)
COLOUR SYSTEM : Select the TV color system from AUTO, PAL, SECAM.
SOUND SYSTEM : Select the TV standard system from DK,I,L/L',BG .
(L' may be not available in some countries)
Menu Operations
Tuning Menu Options Continued
SKIP : If you want skip a channel , pressV+/V- to select ON , and this
channel will be skip next time when you press P+/P- . But you can press
digits button to select the channel . If you want to restore the channel , select OFF.
AFC : Auto frequence control . Select ONto improve the image quality .
FINE TUNE :Press P+/P- to select FINE TUNE item in menu . Then , press V+/V-
button to adjust and improve the image quality .
EXCHANGE : Press V+ to display the menu as follows:
EXCHANGE
FROM :
TO :
1
9
EXCHANGE
Press P+/- to select the item and then V+/- to adjust the channel and V+
to confirm.( For example: pressP+/- to select FROM item, and then press
V+/- to adjust the channel number to 1; then Press P+/- to select TO item,
and V+/- to adjust the channel number to 9; press P+/- to select EXCHANGE item,
and then V+ to confirm. The two channels will be exchanged)
MANUAL SEARCH : Press V+ to start to search the channel . The following menu
will display on the screen:
MANUAL SEARCH
DOWN
UP
Press V+/- to select UP or DOWN, and then press MENU to confirm.
(If you select DOWN, the search will search the lower frequency channel and UP
will search the higher frequency channel)
2. AUTO SEARCH : Auto search and save the channel .Press the V+ button to
start to search the channel and the following menu will appears on the screen:
AUTO SEARCH
NO
YES
Press V+/- to select YES or NO, and menu to confirm.
You could press MENU to stop the search.
NOTE: If you want to search the channels in L or L' system, you need to set the sound
system to L in OSD
TELETEXT
Some menu related function are not available in TELETEXT mode. MENU and AUTO AD
control functions are not available in TELETEXT mode. If the TV is switched on by POWER
after off in TELETEXT mode, or press TV/AV or PC button, the TELETEXT mode will
disappear automatically.
Teletext features may vary depending on the Broadcasting
Companies and is only available if the channel selected is
SLEEP DISPLAY MUTE POWER
NICAM
PC
AUTO AD TV/AV
transmitting Teletext. Pressing the TEXT button whilst in
Teletext operation will switch the current status to TV.
When in Teletext mode, the volume may still be altered to
the desired listening level.
PSM
OK
.SSM
Q.VIEW
P+
V-
MENU
V+
Page Selection
P-
INDEX
TEXT
Pages can beselected in twoways:
a. Press P+ or P- button to increase or decrease the
page number by one.
SUBCODE MIX
TIME
HOLD
SIZE
REVEAL
b. By entering the page number, using the number
keys on the remote control.
SIZE Button
Press SIZE button to change display size : normal large top large bottom
normal
REVEAL Button
Press REVEAL to reveal hidden words e.g. Quiz page answers . Press again
to hide.
Red/Green/ Yellow/CyanButtons
These four buttons correspond to the differently colored subjects .
HOLD Button
Press HOLD button to remain the Teletext page when viewing multi-page
information .
INDEX Button
Press INDEX button to return to the main index page .
Depending on the way information is transmitted , this may have to be pressed
more than once to return to the main index page .
TELETEXT
SUBCODE Button
When Teletext information exceeds more than one page , it may take some time
for the automatic changing of the sub pages to reach the sub page you require .
It is possible to enter your required sub page and continue watching the normal
programme until the correct sub page is found .
Select the required page number using buttons 0-9 .
If the top of the page indicates that sub pages are being transmitted yet the page
does not change . Then the number at the top of the page is there to indicated
that the broadcaster has updated the page s contents , there are no sub pages .
Press SUBCODE button , page number/--- will be displayed at the bottom right
of the screen.
Enter desired sub page number before the page number/--- disappears . To
select page 6 enter 0,0,0 and 6 .
TEXT Button
Press TEXT to enter Teletext mode and only the text page can be visible .
MIX Button
Press MIX button to enter Teletext mode and both the TV picture and text page
can be visible.
TIME
While in normal TV mode only, pressing the button TIME will display the
teletext time in the top right corner for a few seconds.
Note: The teletext buttons could be working even if there is no teletext signal, but there
is no teletext display.
Troubleshooting Guide
To assist in location possible faults use help guide below.
Troubleshooting
Verify ifthe television isproperly plugged.
Verify ifthe television isproperly supplied power.
Verify ifelectricity is available.
No picture, no sound
Verify if correct signals are input.
Press TV/AV button to change signal input to TV input.
Restart the television of power supply is interrupted.
Blank screen
Press MUTE button and verify if Mute mode is set.
Switch to other channel and verify if the same problem
happens.
No sound
Press VOL+ button to see if the problem can be solved.
Verify ifsound system iscorrect. Refer tosome chapter
for adjust.
Poor sound
Verify if correct channel is selected.
Adjust the antenna.
Make adjustments by FINE TUNE and MANUAL SEARCH.
No picture in some
channel
Verify if the same problem exists in other channels.
Check out of picture and sound systems.
Refer to relative instructions in the Manual for color
adjust.
No color for some channel
program (black and white)
Verify ifthe antenna iscorrectly connected.
Verify ifthe antenna isin good condition.
Make fine adjustmentof channel.
Spots with some or
all pictures
Disconnect the televisionfrom power supplyand, 10
seconds later, connect the televisionto the powersupply.
If the problemstill exists, contactauthorized after-sales
service for technicalassistance.
Television out of control
Note:
1.If the fault can not be repaired using the above guide consult with your local authorized service
center.
2.The TV set must only be repaired by a qualified registered service person. Never attempt to
remove the back cover as the TV set has dangerous voltages in side that may cause a fatally or fire.
Specifications
Specifications of the television that you have just purchased may
vary from the information in this table due to technical innovations.
WL19T1
WL22T1
Model
Picture, sound
system
PAL/SECAM-B/G,I,D/K,L,L
1.5W+1.5W
Audio output
COMPONENT input PC input S-VIDEO input Audio input
Video input Antenna input
External input port
~150-240V 50Hz
Power requirements
Power consumption
Temperature
60W
70W
Working:5 C~35 C
Storage:-15 C~45 C
Working:20%~80%
Storage: 5%~90%
Humidity
Remote control
Batteries
Accessories
Owner's manual
Warranty card
Note: Warranty card is only for the special countries and areas.
Note:
All specifications are subject to change without notice.
All quality are approximate value.
V0.1
0090508262I
|