Fully Automatic Washing Machine
User's manual
This manual is for
HWM88-0566T
Special number:0030507833B
Please read this manual
carefully before using.
Retain it for future reference.
Names of the parts
Packing list
Water inlet valve
Top lid component
Control pannel
Water absorption
cushion
One
One
User's manual
Warranty card
Inside the document bag
Inside the document bag
Filter frame
Balance ring
Detergent box
Handle
Components of the water inlet
hose
Power cord
Back cover
Lint filter
Inner tub
One
Inside the accessory bag
Drain hose
Pulsater
Adjustable leg
film
Adjustable leg
Front control board
Cabinet
Tapping screws
Bottom plate
Eight
One
Drain hose frame
Inside the accessory bag
Fixed leg(3 pieces)
Between the upper cushion of the washing
machine package and the upper seal of the
package carton
Meaning and description of the symbols
Automatic washing machine
One
Warning sign
Contents marked with that symbol are related to the
safety of the product and the personal safety of the users.
Please operate in strict conformity to the contents.
Contents marked with that symbol are actions forbidden
to perform. Performing of those action may result in
damage of the machine or influence the personal safety of
the users.
Forbidden sign
1
Safety precautions
Trouble-shooting answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns
sometimes. Please confirm again before sending it to repair. Do not repair it by yourself.
The washing machine must be positioned so that
Please plug the power plug on special
receptacle. Be sure to use three-pins
the plug is accessible. Be sure to pull the plug off
and close the water faucet in following cases:
power failure, delivering the machine, setting the
machine idle or cleaning the machine. Do not plug
or pull the power plug with wet hand.
power receptacle. Ensure that the earthing
prong of the power receptacle is earthed
reliably. Use leakage protector if possible.
Phenomena
The reason
How to settle
Buzzing upon reservation starts,
the digitron displays "E0"
The top lid is not closed
Close the top lid
Put down the drain hose. Open
and close the top lid once.
Clean the foreign material.
Open and close the top lid once.
Is the drain hose put down?
No or slow drain, the digitron
displays "E1" , buzzing.
Earth
Is the drain hose blocked by
foreign material?
Running pauses during spin,
the digitron displays "E2",
buzzing
The top cover leaves open
Close the top lid
Do not bend ,extend,twist,bind by force.Do not press or nip it with weight.
Keep the pin of the power plug clean,if the power plug is polluted with dust,
please wipe with dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is
required to have it replaced by the technicians of our
special shop or our customer care agent.
Re-order the laundries. Close the
top lid.Level the machine in right
position.
Are the laundries put slantingly?
Is the machine slanting?
Safety switch actuates, not
spin, (after self-correction
twice), the digitron displays
"E3", buzzing
Open and close the top lid once.
Open the water tap.
The water tap is not open
No or slow water filling (not
reaching the level in 40 min),
the digitron displays "E4",
buzzing
Push the "Start/Pause" button.
Clean the water inlet valve.
Push the "Start/Pause" button.
Wait for the normal water pressure
Before use.
The water inlet valve is blocked
The water pressureis too low
and the current is too small
In case the washing machine is installed on ground with
carpet, do not block the ventilation hole with carpet.
Do not use water hotter than 50
.
Please contact the after-sales
service department.
The water level sensor is bad.
The digitron displays E6.
Poor or no waterfall flow
If the nozzle is choked with
foreign bodies
Remove the foreign bodies
The ventilation
holes at the bottom
Is there power failure?
Is the power plug loose?
Use it when the power is on.
Soft object
Insert the power plug tightly.
Affusion to the set water level.
Not wash
The machine does
not act
Does the water level arrive at the
set water level?
Is the power plug loose?
Is the top lid closed?
Insert the power plug tightly.
Close the top lid
Not spin
Are the laundries put orderly?
Put the laundries orderly.
Do not put the machine at damp place like
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Is the machine slanting?
Level the machine properly.
Re-order the laundries.
There's abnormal sound inside the
machine
Are the laundries slanting in
spinning?
Is the jointer screw of the water
inlet hose is loose or twisted
awry?
Fasten the jointer screw
properly.
The water faucet leaks
Common phenomena
Phenomena
Explanation
Balance the laundries to avoid slanting.
The spinning is intermittent when it starts.
The wash procedure pauses.
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.
The cloth sensor is detecting , it will add water
after about 48 senconds.
The program is setting the drain time , certain
period is needed before it starts spinning.
Select spin program, but it does not work.
There may be some water flowing out of the
drain hose in the first use of the machine.
It is the water remained performance inspection
by the factory.
2
Disposal after washing
Safety precautions
After using, please clean the lint and foreign materials of the lint filter etc. in time.
Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Do not put hand into the rotating tub. It is dangerous
even if the rotation speed is slow. Take special care of
the children. Keep children away from the washing
machine to avoid them climbing on.
Do not decompose, repair or alter the machine by
yourself.
The lint filter must be used during washing.
It must be cleaned in time after each using.
Clean the detergent box and set it on
the control panel seat.
Lint filter:
1.The method of dismantle: Push it up aslant and gently.
1.Push down the spring piece of the top lint filter to
make the claws out of the filter cover, and then
pull out the lint filter to get it down. figure1
2.Pull the back of the lint filter, and then you can get
down it off the front cover of the lint filter. figure2
3.Sweep the rubbish in the lint filter.
4.Put the back of the lint filter into the front cover .
5.Put the lint filter into filter cover, and make it tight .
6.Make sure the lint filter well installed, or it can
influence your use.
2.The method of install : install it upwards and aslant
and push it in .
Do not wash laundries with volatile materials
(such as thinner, petrol etc.).
Do not put any hot or heavy items (such as the
kettle with hot water) on the washing machine.
Petrol
Benzene
Up
The back cover of lint filter
Up
Dismantle
Install
Dismantle
Install
Dismantle
Install
Down
The front cover of lint filter
Figure 2
Down
The handicapped or children without care shall not use Keep the machine away from direct sunlight and
heat source like the heater.
Figure 1
the machine.
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
The filter screen of the water inlet valve is likely to be
blocked by foreign materials and influence the water
inlet.
Wipe it with neutral detergent.
Please clean it with brush every two months.
Do not wipe it with thinner, petrol, alcohol etc.
Petrol
Benzene
To protect your laundries and washing machine,
please take out all of the coins, buttons, sand,
hairpin and other foreign materials before washing.
Please keep the lint filter in good condition, and
install it to proper position during washing. If the
lint filter is lost or damaged, please contact the local
customer care agent.
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
3.Be sure to pull off the power plug before maintenance.
The cover oflint filter
lint filter
lint filter
Dismantle
Install
Please check if the water faucet is open, and if the
connection of the water inlet pipe is proper.
It is suggested to use foamless washing powder.
The back cover of lintfilter
4.Hang up the power cord and drain hose.
Dismantle
Install
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time
(about 1 hour), then close the top lid.
Installation and adjustment
4 Push the " water level" button, select suitable water level
WATER
LEVEL
Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.
Install the bottom plate
After switching on the power, the washing machine will execute fuzzy program automatically to detect the cloth.
After defection, it can set the water level automatically. To select other water level, first push the "start/pause"
button, then push the "water level" button to set the water level.
After you open the package, please lean the washing
Back
machine gently downon soft items ( like the towel cloth,
blanket, etc. ). Install the bottom plate to the bottom of
the machine with the eight screws by a cross
screwdriver, then lift the machine up gently. See to the
figure:
5 Push the "reserve" button to select suitable reserve
wash program
Front
RESERVE
Bottom plate
Soft items
Screw
After switching on the power, the reserve program is set to off mode automatically. If you need to
set the washing procedure to be finished at reserved time, please push the " reserve "button to
set the reserve wash program. Refer to reserve button in Page 10 for selection.
Adjust the Installation position
Confirm the operation of reserve program
When the "reserve" function is activated, the indicator light of the program you have set
will be off. The "reserve (hour)" and "time remain" indicator lights will be on. During
reserve procedure, push the "reserve" button to display the reserve mode.
To change the running program or cancel the reserve setting, you
The largest allowable slope of the shank base of the machine is 2 .The slanting or rough ground
will result in unstable running or stoppage of the machine. Please adjust it with following methods:
the washing will be finished after 18 hours.
need to switch off the power and make new selection.
Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.
AIR DR
Y
6 Push the "Air dry"button
Attention:
After switiching on the power,the function of the "Air dry" and "reserve"is not selected at
the same time.
Adjust the adjustable leg:
1 .To twist the adjustable leg, please first lift up the
Only after the program with the spin is set,"Air dry"program can be selected;selecting the
other program without spinning,"Air dry"program can not be selected that is the button of
"Air dry"is no reaction.
side of the leg slightly, loosen the adjustable nut,
and twist the leg.
the adjustable nut
Fasten
Loosen
the adjustable leg
High
Low
2 . After adjustment, fasten the nut.
START
PAUSE
7 Push the "Start/Pause" button
6 Finish washing
After finishing wash it'll alarm automatically
How to change the direction of the drain hose
Steps of using the operation buttons and description
of the steps
b
3.Dismantle the drain outlet protecting cover at the other side,
(the way is the same as the drain bushing),then install the drain
bushing, as indicated in Figure 4.
1.Dismantle the rear cover of the washing machine.
2.Put down the drain hose Take off the drain hose
frame as indicated in Figure 1.Take the drain hose into
the cabinet ,then nip the drain fixing clamp to make it
deviated from the clip the other hand is used to put
down the drain bushing,as indicated in Figure 2,3.
4
3
2
1
TIME REMAINED(MINUTES)
RESERVE(HOURS LATER)
RESERVE
SOAK
STANDARD
BLANKET
SAVE
COTTON
1HOUR
2HOURS
WASH
RINSE
SILK
SPIN
4.Extend the drain hose from the other side. Fix the drain hose
with drain hose frame onto the cabinet, as indicated in Figure 5.
RAM
G
O
PR
Drain outlet
protecting cover
4
Drain hose
3
5
Figure 5
Figure 4
Drain hose support
Cabinet
Drain bushing
Figure 2
Drain bushing
Figure 1
5.Install the drain outlet protecting cover to the other side,
as indicated in Figure 6
Inner
Outer
POWER
ON/OFF
Push
Drain bushing
1.Push "power" button to switch on the power
Take do
wn
Drain hose fixing
clamp
Figure 6
PROGRAM
Push
2.Push "program" button to select suitable
full-auto program
Figure 3
Remarks: in order to make sure of the correct of installation, it is suggested to change the direction of the drain hose
with our company serviceman .
After the power is switched on, "standard" is automatically set. To select other full-auto program, please
push the "program" button till the corresponding indicator is on. Refer to the "Program button" on Page 11.
E.g. Set to "SAVE"program for small quantity of laundries with light soil.
Usage the drain hose
The drainage shall be smooth with the drain hose.
1.The height of the drain hose shall be less than 10cm,
or the drainage will not be smooth, and cost such long
time that the machine may stop at mid way.
4.If extra drain hose is needed, please make separate
purchase. The inner diameter of the extra hose shall
not less than 30mm, and the length shall not exceed
1.5m.
3 Push "Process" button to select suitable procedure program
PROCESS
2.Do not step on or press the drain hose.
Attention
Even there's no water in the tub, a certain period is required before spin starting.
Separate the laundries that are not colorfast from other laundries in washing.
The soak procedure can work in cooperation with automatic programs like standard, blanket
cotton. There is intermittent pulsator stirring during soak.
3. If the drain hose is too long, cut it at mid point. To make
smooth drainage, cut the front end of the hose slantingly.
5.If the extra hose is too long, cut it either at A or at B.
After the machine starts operation, you can only set the program and procedure during washing,
and can not make setting in other cases.
5
12
Install the water inlet hose
Confirm the water faucet
"Start/pause" button
"Power" button
After the power is switched on, press it to
start the machine
During working, push it to pause.
During pause, push this button to restart
and go on working
Water faucet,suitable
Push the "power" button to switch on the power.
Under power-on mode, push it to switch off the power.
Push the "power" button to switch on the power. If the
"start/pause" button is not pushed, the machine will
switch off the power automatically after 5 minutes.
Water faucet,not suitable
Outlet end surface
>10mm
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
STANDARD
BLANKET
SAVE
COTTON
1HOUR
2HOURS
Connection between the water inlet hose jointer and the water faucet
SILK
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
PROGRAM
water inlet hose jointer
Screw
Slider
Sign plate
Screw knife
Bushing
Lock level
water inlet hose
Figure 1
Figure 2
Figure 3
"AIR-DRY"button
"Program" button
Following full-auto program is available
Push the "AIR-DRY" button ,then the "AIR-DRY"
indicator light is on, that means the "AIR-DRY"
program is chosen. The purpose isdrying the
inner tub and the outer tub, which can avoid
growing mildew on the outer tub and the inner
tub.
3.Fasten the four screws evenly. See to Figure 4.
4.Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
Program
Standard
Application
Common washing
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.
Washing for coverlet, bigger ,heavy
thickness laundries
Blanket
About 4mm before twisting
Washing for the normal laundries
in short time
Save
Silk
About less than 2mm after twisting
Washing for silk textiles
Screw nut
Washing for cotton textiles
Cotton
Figure 6
Figure 4
Figure 5
5 Use the operation buttons
Connection between the water inlet hose and the washer
a
Description of operation button
1.Do not take off the water absorption cushion. Please check if the
Indicator mode and meaning
Off:
nut of the water
cushion is dropped or damaged before each usage. If it happens
inlet hose
please contact our after-sale department immediately.
Flashing: indicate the running program
2 Put the nut of the water inlet hose on the valve jointer.
3 Fasten the nut. Swing it gently to confirm if it's suitable.
On: indicate the program about to run, or
indicate the selected mode
jointer of the
water inlet valve
water absorption
cushion.
Connection between the jointer of the water inlet hose and the water inlet hose
4
3
2
1
TIME REMAINED(MINUTES)
SOAK
the jointer of the
water inlet hose
WASH
RINSE
1.Push down the slider. Insert the water inlet hose into the jointer.
Slider
Locking level
2 Hang the lock lever to the jointer. Release the slider till a click
sound is heard.
SPIN
RESERVE(HOURS LATER)
RESERVE
Check the connection between the jointer of the water inlet hose
and the water faucet
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
"Process"button
With it you can select one or
several processes of soak,
wash, rinse and spin.
4.Before each usage please check if the connection
between the jointer of the water inlet hose and the
water faucet, and the installation of the water inlet
hose are firm, so as to prevent dropping from
improper installation position.
"Water level" button
"Reserve" button
During the standard program,the washing machine
can detect the laundries automatically. After
detection,it will set the water level to suitable value
among 1, 2,3,and 4 automatically.
You can also set water level by yourself. After the
machine is started, it will not set water level
automatically. You shall push the start/pause
button to make new setting.
The digitron displays remain time
before washing is finished (in minutes)
Push "reserve" button, the digitron
displays the reserve time of washing
(in hours). The indicator flashes to
indicate that the reserve function is
operating.
Dismantle the water inlet hose
1. Close the water faucet.
2. Press the locking lever. Push down the slider. Then pull of the water inlet
hose.
Locking level
Slider
If save program is selected, it will display water
level 2 . When water level 1 is reached in water
filling, it will perform washing while filling water.
When water level 2 is reached, it will change to
normal washing.
Push "reserve" button to display
the reserve mode.
If the machine is used frequently, the jointer of the water inlet hose can be
kept on the faucet to prevent damaging the fixing screw.
1.Preparation before washing
2.Put in the laundries
The capacity of washing of the machine refer to the largest weight of the
Preparation before washing
standard laundries under dry condition that can be washed in one time.
Laundries quantity in one washing cycle shall be lower than the rated
capacity.
1.Connect the water inlet hose
2.Confirm that the washing machine is earthed
reliably. Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put down the drain hose
The thickness ,size , type of the cloth will influence the actual washing capacity.
It is suitable to put in reasonable amount of laundries and the laundries can be
turned round in washing for one time washing.
Add washing powder and softener into
the box directly as per indicated in left figure
3. Usage of detergent
Control panel seat
After adding, close the box.
Washing powder inlet
4.Slanting or uneven ground may result in unstable
working or abnormal noise. Please make the
machine stand horizontally.
Liquid detergent
inlet
Softener inlet
Washing powder box
How to use washing powder
Pay attention to followings before washing the laundries
It is suggested to add washing powder into the box
directly under fuzzy program and reserve program.
Dissolve directly inside the washing machine: (not
applicable for fuzzy and reserve program)
How to use softener
See to the manual of softener for the usage and dosage.
When adding softener into the softener inlet of washing
powder box, note that it shall not exceed the lower side
of the cap.
Do not leave the softener for long period after adding it
into the box. Otherwise it may be solidified and block the inlet.
As the softener is easy to solidify, please clean the box
frequently.(You shall clean it each time you use reserve
function).
The quantity of the
laundries shall not
exceed the rated
value. The big
When the pulsator is
running ,the buttons of
the laundries may cause
noise. For the sake of
discretion ,please put the
laundries with buttons
into other laundries.
Confirm if there's
special requirement
for the laundries.
Clear the pocket.
Take out the coins ,
sand, hairpins etc.
Fasten the buttons
and zippers.
1.Add some water(select the "1" water level)
2.Add washing powder. Run for about 30s to fully dissolve
the Powder. Then push the"start/pause" button.
3.Put in laundries. Select suitable water level. Push the
laundries like the
jeans shall be put
in loosely.
"start/pause" button again.
Quick dissolving of washing powder:
1. Prepare warm water of 30 C and container.
2. Add washing powder while stirring to dissolve it
Before use softener, you must select to sterilize function
completely.
How to use whitener
Please add suitable washing powder as per the laundries
quantity, the set water level and water quantity.
Add water to stipulated level. Dilute the whitener with container,
and then pour it into the liquid whitener inlet slowly.
If you select save program, it is suggested to use liquid
detergent instead of washing powder to guarantee the
washing effect.
It is not recommended to use rich-foam washing powder.
Laundries with color or pattern is not colorfast, thus not applicable.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,
please apply detergent in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.
f. Do not put those laundries polluted by chemicals directly into the washing machine.
For those small laundries and those may get twisting or worn, and woolen/fur laundries, please put them into
mesh bag for washing.
The whitener shall not touch laundries directly.
See to the manual of whitener for the usage and dosage.
For whitener in powder, dissolve it before use.
Washing powder with poor quality or long-time storage may
get caked. Please clean the detergent box duly in usage.
4. Close the top lid
If you open the top lid,the machine will stop working and alarm in spinning process.
|