OFF ROAD TRUCK LIGHT SYSTEM
Model 03029
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
©
®
Copyright 2003 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor FreightTools.
For technical questions, please call 1-800-444-3353.
SAVE THIS INSTRUCTION MANUAL
You will need this Instruction Manual for the safety warnings and precautions, assembly/ inspec-
tion/maintenance information, and assembly diagram. Keep your invoice with this Instruction
Manual. Write the invoice number on the front page. Keep this Instruction Manual and invoice in
a safe and dry place for future reference.
GENERAL SAFETY WARNINGS AND PRECAUTIONS
1.
2.
Use eye protection. Wear ANSI approved safety impact eye goggles when assembling this product.
ANSI approved safety impact eye goggles are available from Harbor FreightTools.
Use the right tool or attachment for the job. There are certain applications for which this product
was designed. Do not modify this product, and do not use this product for a purpose for which it was
not intended.
3.
4.
5.
Replacement parts and accessories: When servicing, use only identical replacement parts. Only
use accessories intended for use with this product.
The Off Road Truck Light System is for OFF ROAD use only. Check with local and/or State
regulations regarding installation and use of this product on your vehicle.
WARNING! Vehicles equipped with airbags may have the sensors located inside the front bumper.
Make sure to consult the vehicle owner’s manual to determine the location of the airbag sensors. To
avoid damaging the sensors if they are located in the front bumper, do not drill holes in the bumper.
6.
7.
The 100 Watt Halogen Lamps become extremely hot under continuous use. Do not touch the
Lamps for at least 30 minutes after turning off the Lamps.
Turn off the Off Road Light System, disconnect its Power Cord from its 12Volt DC Battery, and allow
its Halogen Lamps to completely cool down prior to performing any inspection, maintenance, or
cleaning on the unit.
8.
WARNING! The warnings, precautions, and instructions discussed in this manual cannot cover all
possible conditions and situations that may occur. The operator must understand that common sense
and caution are factors which cannot be built into this product, but must be supplied by the operator.
MANUAL REV 04/05
LIGHT SWITCH
FUSE
(20 AMP)
BLACK
GROUND
WIRE
4
1
BLUE
POWER (HOT)
WIRE
2
TO FUSE BOX
OR
(+) BATTERY
TERMINAL
12 FT. RED EXTENSION WIRE
PASSENGER SIDE
DRIVER SIDE
BLACK
GROUND
WIRES
“Y”
CONNECTOR
FIGURE B
4 FT. RED EXTENSIONWIRE
INSPECTION AND MAINTENANCE
1.
2.
WARNING! Always unplug the Off Road Truck Light System from its 12 Volt DC power source and
allow the unit to completely cool down before performing any inspection or maintenance.
BEFORE EACH USE, inspect the general condition of the Off Road Truck Light System. Check for
misalignment or binding of moving parts, cracked or broken parts, damaged Wiring, damaged Lens/
Lens Guard, and any other condition that may affect its safe operation. If a problem occurs with the
Lights, have the problem corrected before further use. Do not use damaged equipment.
3.
TO CHANGETHE 100WATT HALOGEN BULB, open the Lens Guard and remove the Lens. Using
gloves or a soft cloth, gently press the Bulb to one side of the Socket and remove the opposite end.
Reverse this procedure to install a new Bulb. NOTE: Do not touch the new Bulb with your fingers, as
oil in your skin will damage to the Bulb if not cleaned off before use.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE DIAGRAMS IN THIS MANUAL AS A REFER-
ENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR
WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE
PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE
MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRSTO THE ORIGINAL PRODUCT
OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT
PARTS THERETO.
SKU 03029
For technical questions, please call 1-800-444-3353.
Page 3
|