20” Rolling FlooR Sweep
Model 99989
ASSeMbly, opeRAting, And MAintenAnce
inStRuctionS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
distributed exclusively by Harbor Freight tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVe tHiS MAnuAl.
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
4. Stay Alert - Watch what you are
doing. Use common sense. Do not
operate Tool when you are tired.
that it will operate properly and per-
form its intended function. Check for
alignment of moving parts, binding
of moving parts, breakage of parts,
mounting, and any other condition
that may affect its operation. A guard
or other part that is damaged should
be properly repaired or replaced by a
qualified technician unless indicated
elsewhere in this manual.
5.
wear thick jeans and
steel-toed work boots to
help prevent injury
caused by flying debris.
6. Read and adhere to all safety
precautions provided by the manu-
facturer of your dust collection
system.
SAVe tHeSe
Rolling Sweep use and care
inStRuctionS.
1. Keep children Away - All visitors
should be kept at a distance from
work area.
Specifications
Hose Size
Accepts 4” Dust Collector Hose
20” Wide
Nozzle Size
Dimensions
2. When servicing use only identical
replacement parts.
57” L x 20” W
3. Use Right Tool - Do not use Tool for
any job except that for which it is
intended.
unpAcKing
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please
call Harbor Freight Tools at the number
shown on the cover of this manual as soon
as possible.
4. Do not Force Tool - It will do the
job better and with less likelihood
of injury at the rate for which it was
designed.
5. Store Idle Tools Indoors - When not in
use, Tools should be stored indoors
in dry, and high or locked-up place
- out of reach of children.
Set up inStRuctionS
6. Maintain Tool With Care - Keep tool
maintained to reduce the risk of
injury. Follow instructions for lubricat-
ing and changing accessories. Keep
handles dry, clean, and free from oil
and grease.
Read the entiRe
iMpoRtAnt SAFety
inStRuctionS section at the
beginning of this manual
including all text under
subheadings therein before set
up or use of this product.
7. Check Damaged Parts - Before
further use of the Tool, a guard or
other part that is damaged should
be carefully checked to determine
SKU 99989
For technical questions, please call 1-800-444-3353.
Page 3
Functions
to Attach a Flexible Vacuum Hose
1. This tool can be used to vacuum dust 1. The Swivel Connecting Tube (5) is
and small debris from a shop floor,
when a 4” flexible hose (not included)
from the shop dust collection system
is attached.
designed to accept a standard 4” flex-
ible collection hose (not included).
2. Insert your flexible hose into the Con-
necting Tube (5). If necessary, use a
band clamp or adapter (not included)
to secure the hose.
note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
operating the Sweep
1. The Handle Assembly (8, 13) is de-
signed to swivel on the Connecting
Tube (5).
Assembly
1. Upper Handle Section (13) must be
attached to Lower Handle Section (8)
prior to use.
2. To adjust the swivel angle, loosen
the Knob (4), move the Handle to the
desired position, and retighten the
Knob.
2. Insert Upper Handle Section (13) into
Lower Handle Section (8) and fasten
together using Phillips Head Screw
(15).
3. The Supporting Tube (11) provides
support by pushing on the top of the
Dust Hood (1) as the tool is used.
opeRAting inStRuctionS
4. After attaching the 4” flexible hose,
turn on the shop dust collection sys-
tem (not included). The Sweep will
now operate.
Read the entiRe
iMpoRtAnt SAFety
inFoRMAtion section at the
beginning of this manual
including all text under
5. Roll the sweep along the shop floor to
pick up dust and small debris.
subheadings therein before set
up or use of this product.
6. Pick up large debris by hand to pre-
vent clogging the Dust Hood (1). If
the Dust Hood becomes clogged,
turn off the dust collection system and
clear the Dust Hood.
1. Before operating the Rolling Sweep,
put on ANSI-approved safety goggles
and other safety gear which are sold
separately.
SKU 99989
For technical questions, please call 1-800-444-3353.
Page 4
pleASe ReAd tHe Following
MAintenAnce And
cAReFully
SeRVicing
THe MANUFACTUReR AND/OR DISTRIBUTOR
HAS PROvIDeD THe PARTS LIST AND
to pReVent
SeRiouS injuRy
FRoM tool
ASSeMBLy DIAgRAM IN THIS MANUAL AS
A ReFeReNCe TOOL ONLy. NeITHeR THe
MANUFACTUReR OR DISTRIBUTOR MAKeS
ANy RePReSeNTATION OR WARRANTy OF
ANy KIND TO THe BUyeR THAT He OR SHe
IS qUALIFIeD TO MAKe ANy RePAIRS TO THe
PRODUCT, OR THAT He OR SHe IS qUALIFIeD
TO RePLACe ANy PARTS OF THe PRODUCT.
IN FACT, THe MANUFACTUReR AND/OR
DISTRIBUTOR exPReSSLy STATeS THAT
ALL RePAIRS AND PARTS RePLACeMeNTS
SHOULD Be UNDeRTAKeN By CeRTIFIeD
AND LICeNSeD TeCHNICIANS, AND NOT By
THe BUyeR. THe BUyeR ASSUMeS ALL RISK
AND LIABILITy ARISINg OUT OF HIS OR HeR
RePAIRS TO THe ORIgINAL PRODUCT OR
RePLACeMeNT PARTS THeReTO, OR ARISINg
OUT OF HIS OR HeR INSTALLATION OF
RePLACeMeNT PARTS THeReTO.
FAiluRe: do not use damaged
equipment. if abnormal noise
or binding occurs, have the
problem corrected before
further use.
Procedures not specifically
explained in this manual must
be performed only by a
qualified technician.
cleaning, Maintenance, and
lubrication
1. beFoRe eAcH uSe, inspect the
general condition of the Tool. Check
for loose screws, misalignment or
binding of moving parts, cracked or
broken parts and any other condition
that may affect its safe operation.
2. AFteR uSe, clean external surfaces
of the Tool with clean, moist cloth.
3. Store this tool in a dry location away
from moisture or corrosive materials.
Record product’s Serial number Here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 99989
For technical questions, please call 1-800-444-3353.
Page 5
ASSeMbly diAgRAM
part # description
Qty.
part # description
Qty.
1
2
3
4
5
6
Dust Hood
1
2
2
1
1
1
9
Lock Nut m4
1
1
1
1
1
1
1
Caster Wheel 1.5”
Lock Nut 3/8”
10
11
12
13
14
15
Phillips Head Screw m4 x 35
Supporting Tube
Cap 1/2”
Knob 3/8” x 1-1/2”
Connecting Tube
Upper Handle Section
Handle grip
Phillips Head Screw 3/16” x
3/8”
Phillips Head Screw 1/4” x
3/8”
7
8
Cap 1”
1
1
Lower Handle Section
SKU 99989
For technical questions, please call 1-800-444-3353.
Page 6
liMited 90 dAy wARRAnty
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this prod-
uct is free from defects in materials and workmanship for the period of 90 days from
the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,
criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product. Some
states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation of exclusion may not apply to you. THIS WARRANTy IS exPReSS-
Ly IN LIeU OF ALL OTHeR WARRANTIeS, exPReSS OR IMPLIeD, INCLUDINg THe
WARRANTIeS OF MeRCHANTABILITy AND FITNeSS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the com-
plaint must accompany the merchandise. If our inspection verifies the defect, we will ei-
ther repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return re-
paired products at our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you must bear the cost
of returning the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 99989
For technical questions, please call 1-800-444-3353.
Page 7
|