®
Air Hammer
Model 32940
Assembly and Operation Instructions
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
Copyright© 2004 by Harbor Freight Tools®. All rights reserved. No portion
of this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Manual Revised 11h
9. Maintain tools with care. Keep tools clean for better and safer performance. Follow
instructions for lubricating and changing accessories. Inspect tool cords and air hoses
periodically and, if damaged, have them repaired by an authorized technician. The
handles must be kept clean, dry, and free from oil and grease at all times.
10. Disconnect air supply. Disconnect air hose when not in use.
11. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches are
removed from the tool or machine work surface before connecting the tool.
12. Avoid unintentional starting. Be sure the trigger is released when not in use and be-
fore connecting to the air source. Do not carry any tool with your finger on the trigger,
whether it is connected or not.
13. Stay alert. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.
14. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Check for alignment and binding of moving parts; any broken parts
or mounting fixtures; and any other condition that may affect proper operation. Any part
that is damaged should be properly repaired or replaced by a qualified technician. Do
not use the tool if the trigger does not operate properly.
15. Guard against electric shock. Prevent body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerator enclosures.
16. Replacement parts and accessories. When servicing, use only identical replacement
parts. Use of any other parts will void the warranty. Only use accessories intended for
use with this tool. Approved accessories are available from Harbor Freight Tools.
17. Industrial applications must follow OSHA guidelines.
18. Do not operate tool if under the influence of alcohol or drugs. Read warning labels
if taking prescription medicine to determine if your judgement or reflexes are impaired
while taking drugs. If there is any doubt, do not operate the tool.
19. Use proper size and type extension cord. If an extension cord is required, it must be of
the proper size and type to supply the correct current to the compressor without heating
up. Otherwise, the extension cord could melt and catch fire, or cause electrical damage
to the compressor. Check your air compressor’s manual for the appropriate size cord.
20. Maintenance. For your safety, maintenance should be performed regularly by a quali-
fied technician.
21. Compressed air only. Never use combustible gas as a power source.
22. Use both hands. The force generated from this tool can cause it to break free of your
grasp, causing serious injury and damage. Always operate this tool with both hands.
Note: Performance of the compressor (if powered by line voltage) may vary depending on
variations in local line voltage. Extension cord usage may also affect tool performance.
Warning: The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be under-
SKU 32940
Page 3
stood by the operator that common sense and caution are factors which cannot be
built into this product, but must be supplied by the operator.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities, contain chemicals known [to the State of California] to cause
cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
-
-
-
Lead from lead-based paints
Crystalline silica from bricks and cement or other masonry products
Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.
(California Health & Safety Code 25249.5, et seq. )
Air Hammer Specific Safety Warnings.
1.
2.
Repetitive motions or exposure to vibration may be harmful to your hands and arms.
When wearing gloves to operate the Air Hammer, make sure that the gloves do not
interfere with operating the Trigger (16). Test your gloves with the Trigger (16) before
attaching the unit to an air source.
3.
Never start the tool unless you have a firm grip with both hands and you are positioned
at your workpiece or area.
4.
Before using the Air Hammer, know what is directly underneath the work area or
workpiece. The Air Hammer can quickly penetrate material. If working directly on the
ground, make sure you are not directly above shallow cables, lines, or pipes.
5.
Keep your limbs and body clear of the Air Hammer. If a chisel or bit breaks off, the
tool tends to surge forward suddenly. Make sure the immediate area is clear of other
people or animals. Spectators must stay at a safe distance.
6.
Never point the tool or the air hose (not included) at anyone.
7.
Keep your finger away from the Trigger (16) until you are ready to work.
Warning!! Any spectators in the area will need eye and ear protection.
Beware of flying chips of wood, concrete, metal, or any other material being hammered.
Unpacking
When unpacking, check to make sure all of the parts listed on page 7, Five Chisels,
and a Quick-disconnect Coupler Plug are included. If any parts are missing or broken, please
call Harbor Freight Tools at the number on the cover of this manual as soon as possible.
SKU 32940
Page 4
Assembly / Installation
1.
You will need to prepare the 1/4” Quick-disconnect Coupler Plug to connect to the air
inlet on the Air Hammer. Wrap the Coupler Plug with pipe thread seal tape before
threading it into the Air Inlet (9). Connect the a Quick-Disconnect coupler on a 3/8” ID
Air Source Hose to the tool.
Note: If you are not using an automatic oiler system, before operation, add a few drops of
Pneumatic Tool Oil to the airline connection. Add a few drops more after each hour of
continual use.
2.
Set the air pressure on your compressor to 90 PSI. Do not exceed the recommended
air pressure of 90 PSI.
3.
Check the air connection for leaks. Once you are satisfied there are no leaks, turn off
the air compressor and disconnect the tool.
Air Hammer
1/4” - NPT
For best service you should incorporate an oiler, regulator, and inline filter, as shown in
the diagram above. Hoses, couplers, oilers, regulators, and filters are all available at Harbor
Freight Tools.
NOTE: The information in the box below refers to the Assembly Diagram and Parts
List on page 7.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURERAND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE
IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THATALL REPAIRSAND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT
OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF
REPLACEMENT PARTS THERETO.
SKU 32940
Page 5
Operation
Retainer Spring (15)
Cylinder (14)
Chisel
Trigger (16)
Regulator (4)
Air Inlet (9)
Examine your chisels/bits before using them. If a chisel is dull or cracked do not use
it. Replace worn or broken chisels with approved replacement chisels/bits from
Harbor Freight Tools.
Warning!! Always disconnect the tool from the air source
before examining or changing bits.
1.
Select the appropriate chisel/bit. Unscrew the Retainer Spring (15) and insert the shank
of the chisel/bit. Screw the Retainer Spring (15) back onto the Cylinder (14).
Holding the Air Chisel firmly, pull the chisel/bit hard to make sure it locked into place.
Note: Before connecting the air supply, make sure you are wearing safety goggles and a full
face mask, ear protection, and steel toe shoes.
Warning!! Any spectators in the immediate area will need eye and ear protection.
Beware of flying chips of wood, concrete, metal, or any other material being chiseled.
2.
Connect the air hose to the Air Inlet (9) and turn on the compressor (not included).
3.
Grip the Air Hammer with both hands firmly and put the chisel/bit tip up against the
workpiece you wish to chip.
4.
Gently squeeze the Trigger (16) and move slowly along the workpiece. Do not push
down on the Air Hammer; let it do the work. If it does not do the intended job to satis-
faction, examine your bit to see if it is worn or dull.
Warning!! Always disconnect from the air source before examining or changing bits.
5.
When you are finished, turn off the air supply and then hold the Air Hammer in a safe
direction and Squeeze the trigger to bleed off the remaining air. Then, disconnect the
air hose.
Maintenance
Warning!! Always disconnect from the air source before attempting maintenance.
After each use, wipe the Air Hammer down with a lint free cloth.
1.
2.
3.
Make sure there are no concrete chips, dirt, or debris in the Retainer Spring (15).
Before storage, add a small quantity of high quality pneumatic oil in theAir Inlet (9) and
operate the tool for a couple of seconds to lubricate and protect the internal mechanism.
4.
Examine your chisels/bits before using them. If a chisel is dull or cracked do not use
SKU 32940
Page 6
Maintenance (Continued)
it. Replace worn or broken chisels with approved replacement chisels from Harbor
Freight Tools.
Assembly Diagram
Parts List
Part
Description
Body
Rubber Gasket
O-Ring
Regulator
Control Pin
O-Ring
Qty.
Part
10
11
12
13
14
15
16
17
Description
Rear Valve
Valve Disk
Front Valve
Piston
Cylinder
Retainer Spring
Trigger
Qty.
1
2
3
4
5
6
7
8
9
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Ball
Spring
Air Inlet
Pin
Pin
18
NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
SKU 32940
Page 7
90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability
standards, and warrants to the original purchaser that this product is free from defects in materials and
workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage
due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,
criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event
be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential
damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY
IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If
our inspection verifies the defect, we will either repair or replace the product at our election or we may elect
to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return
repaired products at our expense, but if we determine there is no defect, or that the defect resulted from
causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
SKU 32940
Page 8
|