DRYWALL DOLLY
900 LB. CAPACITY
94883
ASSEMBLY & OPERATING INSTRUCTIONS
Due to continuing improvement, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions and replacement parts please call 1-800-444-3353.
9. Do not exceed the product’s maximum load capacity of 900 Lbs. Always make sure the
load is evenly distributed on the Dolly.
10. Only use on a flat surface capable of supporting the Drywall Dolly and its maximum
capacity load of 900 Lbs. It is easy to lose control of the Drywall Dolly if attempting to pull a
load on a sloping or uneven surface.
11. Do not allow children to play on, stand upon or climb on the Drywall Dolly. The Drywall
Dolly is not for carrying people or animals.
12. Always check hardware and parts after assembling. All connections should be tight and
hardware tightened.
13. Always distribute objects in the Drywall Dolly evenly. Uneven weight distribution could
cause tipping. Harbor Freight Tools is not responsible for damage to persons or cargo.
14. Be aware of dymanic loading! Suddenly dropping or bouncing a load on the Drywall Dolly
may create, for a brief instant, an excess load, which may result in damage to the product and/
or personal injury.
Warning:
The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions and situations that may occur. It must be understood by
the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
Unpacking
When unpacking your Drywall Dolly, check to make sure the following parts are included. If any
parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353.
Assembly
Your Drywall Dolly will require complete assembly. It is important that you read the entire manual to
become familiar with the product BEFORE you assemble and use the Dolly. Before operating the
Drywall Dolly, be sure that you have all parts described in the Parts List and Assembly Diagram
page 5 of this manual.
1.
2.
3.
Set the Caster Base (B) down on your work bench or work surface. Locate both 8” Swivel
Casters (C). The 8” Swivel Casters (C) will be installed on the front (narrow) side of the
Caster Base (B).
Set the 8” Swivel Casters (C) so the holes in the plate line up with the holes in the Caster
Base (B). Insert four Bolts (1) up through the plate and Caster Base (B), slide on Washers
(2), and thread on Locknuts (3)-see Assembly Diagram.
Install the 8” Rigid Casters (D) on the rear of the Caster Base (B). Set the 8” Rigid
Casters (D) so the holes in the plate line up with the holes in the Caster Base (B). Insert four
Bolts (1) up through the plate and Caster Base (B), slide on Washers (2), and thread on
Locknuts (3)-see Assembly Diagram.
4.
Set the ends of the down tubes on Handle (A) into the fittings on the Caster Base (B)-see
Assembly Diagram. Insert one Bolt (4) through the down tube of the Handle (A) and through
the fitting. Slide on Washers (5), and thread on Locknuts (6).
SKU 94883
For technical questions please call 1-800-444-3353.
Page 3
Operation
1.
2.
Place the load onto the Caster Base (B). Do not exceed the maximum weight capacity of
900 Lbs. Make certain the load is evenly distributed on the Drywall Dolly, and that it is
resting adequately on the Handle (A).
Using two hands to grasp the Handle (A), move the Drywall Dolly with its load. Lead with the
8” Rigid Casters(D), so that you can control the direction and movement of the Dolly easier.
Caution:
Always use two hands when moving the Drywall Dolly. This provides support
in case one hand slips while moving a load.
Parts List
Part # Description
Quantity Part # Description
Quantity
A
B
C
D
Handle
1
1
2
2
1
2
3
4
5
6
M10 X 20 Bolt
10 Washer
M10 Locknut
M8 X 45 Bolt
#8 Washer
16
16
16
4
4
4
Caster Base
8” Swivel Caster
8” Rigid Caster
M8 Locknut
Note: Some parts are listed and shown on Page 5 for illustration purposes only and are not
available individually as replacement parts.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY
KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
SKU 94883
For technical questions please call 1-800-444-3353.
Page 4
Assembly Diagram and Warranty
LIMITED 90 DAY
WARRANTY
Harbor FreightTools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for
the period of ninety days from the date of purchase. This warranty does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, or to lack of
maintenance.We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent,
special or consequential damages arising from the use of our product. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our
inspection verifies the defect, we will either repair or replace the product at our election or we may elect to
refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return
repaired products at our expense, but if we determine there is no defect, or that the defect resulted from
causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 94883
For technical questions please call 1-800-444-3353.
Page 5
|