Installation
1. The safe has four concrete fasteners that
are inside of the safe when you open
it. There is also a mounting template
included with the safe. Place the mounting
template against the area you will be
mounting the safe and tape it into place.
3. To use the concrete fasteners, drill a
small pilot hole through the template
to mark the hole placement. Next drill
four holes in the correct location, using
a concrete drill bit. Drill the holes the
same diameter as the fasteners and 2"
deep. Hammer the fastener in the hole
with the flat side going into the hole first.
Use a wood block between the bolt and
the hammer to protect the threads.
WARNING! Before drilling or driving
nails, make sure there are no wires,
cables or pipes in the path.
2. To attach the safe to a wood surface,
hammer a nail (not included) to
4. Place the safe over the bolts (with
the nut removed from the bolts)
mark the hole placement. Drill an
1/8"diameter pilot hole into each
mounting hole location. Place the safe
over the mounting holes and secure
the safe using four 1/4" diameter
self-tapping screws (not included).
and tighten a nut onto each bolt. As
you tighten the nuts onto the bolts,
the fasteners will expand inside the
cement, securing the safe into place.
Operation
1. To Open the Safe: Input the numbers
“159” on the Electronic Key Pad, then
press either the “A” or “B” Key. Once the
Green light is on, turn the Knob and pull
the Door open. Note: The knob must be
turned within 5 seconds of the Green light
coming on. If the knob is not turned, the
entry code will need to be re-entered.
you can input the new Code (1 to 8
characters) into the Front Control Panel,
followed by either the “A” or “B” Key.
The Safe will beep twice to confirm that
the Code has been changed. Important:
If the Safe beeps three times, then
the Code has not been accepted, and
you must repeat the steps above.
2. To Close: Close the Door and turn
the Knob in the opposite direction.
The Safe is now locked.
4. To Change the Batteries: If the Red
Light and the Green Light are both lit
at the same time, it is time to change
the Batteries. Follow the instructions
for opening the Safe. The Battery
3. To Change the Code: The Safe comes
preset with a default code of “159.”
To change the Code, first follow the
instructions for opening the Safe. On
the inside of the Door toward the hinge,
you will see a small Red Button. Press
this Button until the Yellow Light on
the Front Control Panel lights up. Now
Compartment is located on the inside
of the Door. Slide the Battery Cover off
of the Battery Compartment, remove
used Batteries, and insert four new
“AA” Batteries. Once you have changed
the Batteries, be sure to test the Code
before you close the Door again.
REV 02d, 04c, 07b
Item 45891
For technical questions, please call 1-800-444-3353.
Page 3
5. Using the Emergency Key:
c. Turn Knob and pull Door open.
a. Peel off the Label directly to the
left of the keypad to reveal the
Secret Key-Operated Lock.
d. Replace the Keypad and the
Label when finished.
IMPORTANT: NEVER LOCK THE
EMERGENCY KEYS IN THE SAFE!
b. Insert Emergency Key into the
Secret Key-Operated Lock.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Record Serial Number Here:
Note: If product has no serial number, record
Note: Replacement parts are
month and year of purchase instead.
not available for this item.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
REV 04a, 07b
|