18V cordless Worklight
67032
set up and operating instructions
note: BatterY pack (67029) sold separatelY
®
distributed exclusively by harbor Freight tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
saVe this manual.
©
®
Copyright 2009 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
b. prevent unintentional starting.
ensure the switch is in the off-
position before connecting to bat-
tery pack, picking up or carrying
the tool.
d. under abusive conditions, liquid
may be ejected from the battery;
avoid contact. if contact acciden-
tally occurs, flush with water. If
liquid contacts eyes, additionally
seek medical help. Liquid ejected
from the battery may cause irritation
or burns.
4. Flashlight use and care
a. do not use the Flashlight if the
switch does not turn it on and off.
6. service
b. disconnect the battery pack from
the Flashlight before making any
adjustments, changing acces-
sories, or storing the Flashlight.
Such preventive safety measures
reduce the risk of starting the Flash-
light accidentally.
a. have your Flashlight serviced by
a qualified repair person using
only identical replacement parts.
This will ensure that the safety of the
Flashlight is maintained.
Flashlight safety Warnings
c. maintain the Flashlight. check
for misalignment or binding of
moving parts, breakage of parts
and any other condition that may
affect the Flashlight’s operation.
if damaged, have the Flashlight
repaired before use.
1. Maintain labels and nameplates on
the tool. These carry important safety
information. If unreadable or miss-
ing, contact Harbor Freight Tools for a
replacement.
2. Avoid unintentional starting. Prepare
to begin work before turning on the
tool.
5. Battery tool use and care
a. recharge only with the charger
specified by the manufacturer. A
charger that is suitable for one type
of battery pack may create a risk of
fire when used with another battery
pack.
3. Do not leave the tool unattended
when it is attached to a battery pack.
Turn off the tool, and disconnect it
from its battery pack before leaving.
4.
The battery charger gets
hot during use. The
charger’s heat can build
b. Use tools only with specifically
designated battery packs. Use of
any other battery packs may create
a risk of injury and fire.
up to unsafe levels and
create a fire hazard if it does not
receive adequate ventilation, due to
an electrical fault, or if it is used in a
hot environment.
Do not place the charger on a flam-
mable surface. Do not obstruct any
vents on the charger. especially
avoid placing the charger on car-
pets and rugs; they are not only
c. When battery pack is not in use,
keep it away from other metal ob-
jects, like paper clips, coins, keys,
nails, screws or other small metal
objects, that can make a connec-
tion from one terminal to another.
Shorting the battery terminals to-
gether may cause burns or a fire.
SKU 67032
For technical questions, please call 1-800-444-3353.
Page 3
flammable, but they also obstruct
vents under the charger.
symbology
Place the charger on a stable, solid,
nonflammable surface (such as a
stable metal workbench or concrete
floor) at least 1 foot away from all
flammable objects, such as drapes or
walls. Keep a fire extinguisher and a
smoke detector in the area. Fre-
quently monitor the charger and
battery while charging.
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts Alternating Current
Amperes
V~
a
5. This product is not a toy. Keep it out
of reach of children.
No Load Revolutions per Minute
(RPM)
n xxxx/min.
0
6. People with pacemakers should
consult their physician(s) before use.
Electromagnetic fields in close prox-
imity to heart pacemaker could cause
pacemaker interference or pacemak-
er failure. In addition, people with
pacemakers should:
• Avoid operating alone.
• Properly maintain and inspect to
avoid electrical shock.
7. The warnings, precautions, and in-
structions discussed in this instruction
manual cannot cover all possible con-
ditions and situations that may occur.
It must be understood by the operator
that common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
saVe these
instructions.
extension cords
note: Extension cords must not be used
with this item’s charger.
SKU 67032
For technical questions, please call 1-800-444-3353.
Page 4
speciFications
operating instructions
Battery Type 18V NiCd - SKU 67029
tool set up
Charger
Bulb
SKU 67031
to preVent
serious injurY
From accidental
10W incandescent, XPR-18
Accessories Spare Bulb in Lamp Head Housing
operation:
turn the power switch of the
tool to its “oFF” position and
disconnect the tool from its
Battery pack before
performing any inspection,
maintenance, or cleaning
procedures.
unpacking
When unpacking, make sure that the
item is intact and undamaged. If any parts
are missing or broken, please call Harbor
Freight Tools at 1-800-444-3353 as soon
as possible.
charge the Battery
instructions For
putting into use
The Charger (SKU 67031) and
Rechargeable Battery Pack (SKU
67029) are sold separately. Please
refer to the 67031 Charger manual
for important safety warnings and
proper instructions on charging tool.
read the entire important
saFetY inFormation
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
Warning! Do NOT use a different
Charger or Battery Pack to power this
tool.
note: For additional information regarding
the parts listed in the following pages,
refer to the Parts List and Assembly
Diagram near the end of this manual.
general operating instructions
1. Attach the fully charged Battery Pack
(sold separately) to the base of the
Flashlight.
Functions
Power Switch (2)
Lamp Head Housing (7)
2. Slide the Power Switch (2) to ON
by sliding it towards the Lamp Head
Housing (7).
3. Adjust the direction of the light by
pivoting the Lamp Head Housing (7)
of the light clockwise, up to 90°.
Lens Retainer (15)
4. Turn off the Flashlight and disconnect
its power supply after use. Clean,
then store the tool indoors out of chil-
dren’s reach.
Battery Pack
(SKU 67029)
(Sold Separately)
Figure 1
SKU 67032
For technical questions, please call 1-800-444-3353.
Page 5
Lamp Head Housing (7)
Spare Bulb (12)
maintenance and
serVicing
Reflector (13)
Lens (14)
Lens Retainer (15)
Procedures not specifically
explained in this manual
must be performed only by a
qualified technician.
to preVent
serious injurY
From accidental
Spring (11)
Bulb (12)
operation:
Figure 2
3. To change the bulb:
turn the power switch of the
tool to its “oFF” position and
disconnect the tool from its
battery pack before
performing any inspection,
maintenance, or cleaning
procedures.
a. Unthread the Lens Retainer (15)
counterclockwise and carefully re-
move the Lens (14), Reflector (13)
and spent Bulb (12), noting which
side of the lens faces the Reflector.
b. Slide the spare bulb (12) (included)
out of its slot in the Lamp Head
Housing (7) and place it in the
Spring (11) in the center of the Lamp
Head Housing.
to preVent serious
injurY From tool
Failure:
do not use damaged
equipment.
c. Replace the Reflector, the Lens, and
cleaning & maintenance
the Lens Reflector.
1. BeFore each use, inspect the
general condition of the tool. Check
for loose hardware, misalignment or
binding of moving parts, cracked or
broken parts, damaged electrical wir-
ing, and any other condition that may
affect its safe operation.
note: Purchase a new spare bulb to store
inside the Lamp Head Housing for
future use.
2. aFter use, wipe external surfaces
of the tool with clean cloth.
SKU 67032
For technical questions, please call 1-800-444-3353.
Page 6
parts & assemBlY diagram
part
description
Qty
1
part
description
Qty
1
2
1
1
1
1
2
5
1
2
3
4
5
6
7
8
9
Strap
11 Spring
Power Switch
1
1
12 Bulb, XPR-18
13 Reflector
Switch
Housing
1
14 Lens
Tapping Screw ST2.9 x 16
Rotation Limiting Plate
Lamp Head Housing
Clamp Plate
2
1
1
1
15 Lens Retainer
16 Contact Plate
17 Contact Strip
19 Tapping Screw ST2.9 x16
20 Housing
Wiring Board
1
1
10 Positive Spring
1
record product’s serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 67032
For technical questions, please call 1-800-444-3353.
Page 7
please read the FolloWing careFullY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLy
DIAgRAM IN THIS MANUAL AS A REFERENCE TOOL ONLy. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANy REPRESENTATION OR WARRANTy OF ANy KIND TO THE BUyER THAT
HE OR SHE IS qUALIFIED TO MAKE ANy REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
qUALIFIED TO REPLACE ANy PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR EXPRESSLy STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN By CERTIFIED AND LICENSED TECHNICIANS, AND NOT By THE BUyER. THE
BUyER ASSUMES ALL RISK AND LIABILITy ARISINg OUT OF HIS OR HER REPAIRS TO THE
ORIgINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISINg OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
limited 90 daY WarrantY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this prod-
uct is free from defects in materials and workmanship for the period of 90 days from
the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,
criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product. Some
states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation of exclusion may not apply to you. THIS WARRANTy IS EXPRESS-
Ly IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDINg THE
WARRANTIES OF MERCHANTABILITy AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the com-
plaint must accompany the merchandise. If our inspection verifies the defect, we will ei-
ther repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return re-
paired products at our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you must bear the cost
of returning the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 67032
For technical questions, please call 1-800-444-3353.
Page 8
|