Customer Service
N53 W24700 South Corporate Circle
Sussex, WI 53089
U.S.A.
A Huffy Company
Model 89780
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY
RESULT IN SERIOUS INJURY,
PROPERTY DAMAGE AND WILL VOID WARRANTY.
This unit is intended for display purposes only and
should not be used for play.
BASKETBALL
BALL
CENTER
BASKET
To ensure safety, do not attempt to assemble this system without
following the instructions carefully. Check entire box and inside all
packing material for parts. Before beginning assembly, read the
instructions and identify parts in this document. Proper and
complete assembly, use and supervision is essential for proper
operation and to reduce the risk of accident or injury. A high
probability of serious injury exists if this system is not installed,
maintained, and operated properly.
CENTER
•
•
•
•
•
During assembly, if using a ladder use extreme caution. Two
people are recommended for this operation.
If technical assistance is required, contact Huffy Sports’ Sample
and Display Technician.
Serious injury could occur if teeth/face come in contact with
backboard, net or rim.
Display recommended for 3” (7.6 cm) or 3-1/2” (9 cm) Round or 4”
(10 cm) Square poles only.
All instructions and warnings MUST accompany any display item
that is sold.
REQUIRED TOOLS AND
MATERIALS:
Wrenches: (Two each) 7/16”, 1/2”, 9/16”,
and 3/4” or Pliers
•
Most injuries are caused by misuse and/or not following
instructions.
Use caution when installing this unit.
•
•
3/16” Allen Wrench
Step Ladder, 8 ft. (2.4 m)
IMPORTANT!
To ensure prompt and correct handling of any problems, or to answer any questions, please contact the Sample
and Display Technician at 1-800-558-5234.
P/N 211487C
04/02
1
Move display to location on sales floor and
remove 2 X 4 runners under feet.
9
1
11
P.O.P.
Install pegboard panels onto
corresponding side support
railings. Secure with zip tie to
temporarily hold panel in place.
Remove zip ties after assembly is
complete. Attach P.O.P. sign (11)
with plastic push clips (9) so that it
faces aisle as shown.
2
FRONT
P/N 211487C
04/02
3
WARNING
Install support railings, as shown. Insert
particle board as shown and rest on second
support railing.
3
TWO PERSON MINIMUM
REQUIRED FOR THIS
PROCEDURE. NOT
FOLLOWING
RECOMMENDATION MAY
RESULT IN BODILY INJURY.
IMPORTANT:
Top Support Railing Must
Be Inserted In The Positions
Shown. POP Cards Will
Later Be Inserted Into Rail
Slots.
NOTE:
Top shelf has
square
corners.
NOTE:
Location of
tab on lower
panel.
NOTE:
Use shorter
bolts to
assemble.
FRONT
P/N 211487C
04/02
4
Install enclosed pole mounting hardware and pole
for each assembly.
WARNING
4
TWO PEOPLE ARE
NECESSARY TO MOUNT THE
ELEVATOR ASSEMBLY TO
THE POLE. ONE PERSON
SHOULD NOT ATTEMPT TO
DO THIS ALONE.
908811
C
3-1/2” Rnd. Pole X 30” Pole
Upper Support
Railing
B
3-1/2” Rnd. Pole
D
3-1/2” Rnd. Pole
TOP
VIEW
3-1/2” Rnd. Pole
A
NOTE:
FRONT
Enclosed One Set
Of Hardware For
(Each) Pole Installation
P/N 211487C
04/02
5
Assemble display products per diagram below and
procedures on following pages for each model. Then
mount to corresponding backboard hardware.
WARNING
5
TWO PERSON MINIMUM
REQUIRED FOR THIS
PROCEDURE. NOT
FOLLOWING
RECOMMENDATION MAY
RESULT IN BODILY INJURY.
81410
48” Fan Backboard
w/Slam Jam Rim
MOUNTING THE ELEVATOR
ASSEMBLY TO THE POLE IS
PERFORMED AT AN
C
HUFFY TUFF
ELEVATED HEIGHT. USE
PROPER PRECAUTION.
D
89036 44” SFA
w/Slam Jam Rim
Steel Framed Acrylic
LINE-UP
73092
44” Fan
Backboard
w/Slam Jam Rim
CLEAR SLAM
B
INSTALLATION
DIAGRAM
A
FREE
STYLE
80550
44” Fan
w/Standard Rim
FRONT
P/N 211487C
04/02
6
Pole Locations
C
A B
D
Refer To Combo For
Goal Assembly
Instructions
Mount extension arm and
rim to backboard and
finger tighten.
1.
NOTE: For spring
loaded rim assembly,
refer to instructions
included with rim
hardware.
2.
Secure hardware to extension
arm as shown and tighten
completely. install pole cap (2)
2
5
6
6
3
10
9
P/N 211487C
04/02
7
Insert header cards (8) into place as shown.
6
BASKETBALL
CENTER
BASKETBALL
CENTER
8
P/N 211487C
04/02
8
|