800-08115 1/11 Rev. B
GSMVLP5 GSM and
ILP5 Ethernet
Communications Modules
Installation and Setup Guide
Installing Communication Modules
RF Exposure
WARNING: The antenna(s) used for this transmitter must be installed to provide a separation distance of
at least 20 cm from all persons and must not be co-located or operating in conjunction with any other
antenna(s) or transmitter.
Installing the GSMVLP5 in the LYNX Touch Series Control
Ensure that SIM card and the connector board are securely installed in the GSMVLP5 before installing the
module in the LYNX Touch.
1. Install the provided FCC/IC label (P/N 800-08334) on the control’s case back (refer to Figure 1).
LYNX TOUCH SERIES
FCC ID: CFS-8DLLYNXTOUCH1
IC: 573F-LYNXTOUCH1
IC MODEL: LYNXTOUCHG1
CONTAINS TRANSMITTER MODULE
FCC ID: QIPMC55I
IC: 7830A-MC55I
800-08334 2/11 Rev
A
LYNX TOUCH SERIES
THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES AND RSS 210 OF INDUSTRY
CANADA. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS
DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
COMPLIES WITH FCC RULES, PART 68 FCC REGISTRATION NO.: AC3AL05BL5000
RINGER EQUIVALENCE: 0.1B
800-08126 1/11 Rev
A
5000-100-186-V0
Figure 1. FCC/IC Label Location
2. Release the LYNX Touch front case from the back case by depressing the two locking tabs at the top of the
unit with the blade of a medium size screwdriver (Refer to Figure 2).
3. Install the GSMVLP5 into the LYNX Touch control front case. Ensure that the connector board is properly
seated into the receptacle on the control (Refer to Figure 2).
4. Secure the GSMVLP5 with the three provided screws (Refer to Figure 2).
5. Enable the GSMVLP5 device, configure alarm reporting and module supervision and register the device.
Refer to the “Program the Radio” and “Diagnostics” sections in the LYNX Touch Series Installation and
Setup Guide (P/N 800-06834 or higher).
For Documentation and Online Support: http://www.security.honeywell.com/hsc/resources/MyWebTech
ETHERNET CABLE
TO ILP5
RJ45 RECEPTACLE
LYNX TOUCH
REMOVE ILP5
KNOCKOUT
REMOVE ILP5
SPACER
ALTERNATE INSTALLATION
ILP5 SPACER
RJ45
RECEPTACLE
CONNECTOR
BOARD
ROTATED
TIE
WRAP
180
(1)
TIE
WRAP
POINT
CONNECTOR BOARD
SCREW
(3)
ILP5
RECEPTACLE
LYNX TOUCH
LOCKING TABS
5000-100-154-V1
Figure 3. Installing the ILP5 in the LYNX Touch
Electrical Specifications
GSMVLP5
Voltage Input
Current
Idle
5V
15 mA, standby
300mA, average transmit
1.6A peak transmit, 25% duty cycle
Average
Peak
ILP5
Voltage Input
Current:
5V
83 mA, 100 Base T with traffic
41 mA, 10 Base T with traffic
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2011 Honeywell International Inc.
Ê800-08115!Š
800-08115 1/11 Rev. B
|