Instruction booklet
TUMBLE DRYER
Contents
GB
GB
Important information, 2
Product data, 2
English
Installation, 3-4
Where to put your dryer
Ventilation
Electrical connection
Levelling your dryer
Before you start using your dryer
Dryer description, 5
The front
The back
Control panel
Start and programmes, 6
Choosing a programme
VTD 6000
Laundry, 7-8
Sorting your laundry
Wash care labels
Special clothing items
Drying times
Warnings and Suggestions, 9
General safety
Saving energy and respecting the environment
Maintenance and Care, 10
Switching off the electricity
Cleaning the filter after each cycle
Check the drum after each cycle
Cleaning the dryer
Troubleshooting, 11
Service, 12
Disposal
Hotpoint Guarantee, 15
Hotpoint After Sales Service, 16
! Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and
should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the
dryer so that the new owner may be informed about warnings and suggestions on how the appliance works.
! Read these instructions carefully; the following pages contain important information on installation and suggestions
on how the appliance works.
1
Installation
Permanent venting
Where to put your dryer
GB
In conjunction with the vent tube we recommend
using a Wall/Window Vent Kit, available at a retail
location or the nearest Spare Parts Dealer.
●
Place your dryer at a distance from gas ranges,
stoves, heaters, or cook tops because flames can
damage the appliance.
●
If you are going to install the
Minimum gap 10mm
Wall mounting
appliance under a work
1. Leave an opening in
the wall to the left of the
dryers proposed position.
2. Keep the tube as short
and straight as possible
to prevent condensed
moisture from backing up
into the dryer.
3. Similarly, the duct in
the wall should slope
downwards towards the
outside.
counter, be sure to leave a
10mm space between the
top and any other objects on
or above the machine and a
15mm space between the
sides and lateral furnishings
Minimum gaps
15mm
or walls. This is to ensure
proper air circulation. Make sure that the back
vents are not obstructed.
●
Make sure you put your dryer in an environment
that is not damp and has proper air circulation
throughout, the dryer will not operate efficiently in
an enclosed space or cupboard.
Window mounting
1. With a stacked dryer
the hole in the window
should ideally be made
below the vent.
! We do not recommend that the dryer is installed in a
cupboard but the dryer must never be installed
behind a lockable door, a sliding door or a door with a
hinge on the opposite side to that of the dryer door.
2. The tube should be
kept as short as possible.
Ventilation
The Dryer dries your laundry by drawing in cool, clean
and relatively dry air, heating it, and then distributing it
through the clothes as they are gently tumbled. For
optimum performance, the moist air is then blown out
through a vent tube at the back of the dryer.
When the dryer is in use, there has to be adequate
ventilation to avoid the back flow of gases into the room
from appliances burning other fuels, including open fires.
Depending on how often you use your dryer, it is
essential that areas A and B are checked periodically
to remove lint or debris.
The vent tube adaptor must be fitted securely thus
preventing any humid air from being emitted back into
the room.
! The Dryer should not be pushed so far back that the
tube adaptor is pulled out of position or the tube is
squashed or bent.
Mobile venting
! The tube should be kept clear of the air intake vent
and kinks or ‘U’ bends must be avoided as these will
obstruct the tube or trap condensation.
A vent tube must always be fitted when the dryer is
used in conjunction with Mobile Venting.
The tube must be fitted securely into the back of the
dryer (see Dryer Description). If possible, it is always
best to connect the tube to a permanent
outlet close to the dryer. If permanent installation is
not possible, the dryer will work just as well with the
tube passing through a partly-opened window.
! Ensure that the end of the tube is not directed
toward the air intake vent at the rear of the dryer.
! The vent tube should not exceed 2.4 metres in
length and should be kept free of any possible
accumulation of fluff, lint and water by shaking it out
frequently. Always ensure that the tube is not
squashed.
3
Installation
Open window venting
Moulded plug
GB
The end of the tube
! The plug must not be used
without the fuse cover in place. If
a replacement fuse holder/cover is
required, it must be of the same
colour coding or wording as
shown on the base of the plug.
Replacements are available from
authorised dealers.
should be directed
downwards, to prevent
warm moist air from
condensing in the room or
in the dryer.
Changing the plug
The wires in the power cord are coloured in accordance
with the following:
Green and Yellow
(Earth) wire to terminal
! Ensure that the dryer is adequately ventilated and
that the end of the vent tube is not directed towards
the air intake duct.
marked ‘E’, symbol
or coloured green and
yellow.
,
! The vent tube must always be fitted for optimum
performance.
! Make sure that the vent tube and air intake vents are
not obstructed or blocked.
! The dryer must not recycle exhaust air.
! Misusing a tumble dryer may create a fire hazard.
! Do not discharge exhaust air into a flue which is
used for exhaust fumes from other appliances that
burn gas or other fuels.
! Do not discharge exhaust air into an extraction
system or any duct with an extractor fan. This will
affect the way the thermal controls operate and can
result in a fire hazard.
13A ASTA approved
fuse to BS1362.
Blue (Neutral) wire to
terminal marked ‘N’ or
coloured black.
Brown (Live) wire to
terminal marked ‘L’ or
coloured red.
Cord clamp
! If the plug being replaced is a non-rewirable type,
then the cut-off plug must be disposed of safely. DO
NOT leave it where it can be inserted into a socket
and create a shock hazard.
! The power supply cord should be checked periodically
and replaced by a cord specially prepared for this
dryer and fitted only by authorised technicians (see
Service). New or longer power cords are supplied at
an extra charge by authorised dealers.
Electrical connections
! The manufacturer denies any responsibility should
any of these rules not be followed.
! If in doubt about any of the above consult a qualified
electrician.
Make sure of the following before you insert the plug
into the the electrical socket:
●
The socket must be grounded.
●
The socket must be able to sustain the machines
maximum power, which is indicated on the rating
label (see Dryer Description).
Levelling your dryer
The dryer must be installed level for correct operation.
When you have installed your
dryer in its final location check
that it is level first side to side,
then front to back.
●
Power voltage must be within the values indicated
on the rating label (see Dryer Description).
The socket must be compatible with the dryers
plug. Should this not be the case, replace the
plug or the socket.
●
! The dryer must not be installed outdoors, even if the
space is sheltered. It can be very dangerous if it is
exposed to rain or storms.
! Once installed, the dryers electrical wire and plug
must be within easy reach.
If the dryer is not level, use a
wooden block to
support it while adjusting the two
front legs up or down, until your
dryer is level.
! Do not use extension cords.
! The power cord must not be bent or squashed.
! The power cord supplied is fitted with a BS1363 plug
and a 13 amp BS1362 fuse. If you need to replace the
fuse, use only those rated at 13 amp (13A) and ASTA
approved to BS1362.
Before you start using your dryer
Once you have installed your dryer and before you
use it, clean the inside of the drum to remove any dust
that could have accumulated during transport.
4
Dryer Description
The front
The back
GB
Drum
Control Panel
Air Intake Vent
Rating plate
Vent Tube fitted here
Model & Serial
numbers
Caution: Hot!
Filter
Control panel
START
Button
Indicator
HEAT
Button
TIMER
Knob
The START button begins drying a selected
programme (see Start and Programmes).
The TIMER knob sets the drying time: rotate it clockwise,
never counter-clockwise, until the indicator is pointing
to the drying time you want to select (see Start and
Programmes).
The HEAT button selects drying temperature (see
Start and Programmes).
OUT: LOW heat
IN: HIGH heat
5
Start and Programmes
Choosing a programme
6. Press the START button to begin.
GB
During the drying programme, you can check on
your laundry and take out items that are dry
while others continue drying. When you close
the door again, press the START button in order
to resume drying.
1. Plug the dryer into the electrical socket.
2. Sort your laundry according to fabric type (see
Laundry).
3. Open the door and make sure the filter is clean
7. About 10 minutes before the programme is
completed, it enters the final COOL TUMBLE
phase (fabrics are cooled), which should always
be allowed to complete.
and in place (see Maintenance).
4. Load the machine and make sure items are not
in the way of the door seal. Close the door.
8. Open the door, take the laundry out, clean the
5. Choose the drying time by checking the Drying
Guide table for the type of fabric you are drying
(see Laundry).
filter and replace it (see Maintenance).
9. Unplug the dryer.
- Set the temperature with the HEAT button.
- Select a drying time by rotating the TIMER knob
clockwise.
6
Laundry
Sorting your laundry
Wash Care Labels
GB
●
Check symbols on clothing labels to make sure
that the articles can be tumble dried.
Sort laundry by fabric type.
Empty pockets and check buttons.
Close zippers and hooks and tie loose belts and
strings.
Wring out each item in order to eliminate as much
excess water as possible.
Look at the labels on your garments, especially when
tumble drying for the first time. The following symbols
are the most common:
●
●
●
May be tumble dried
●
Do not tumble dry
! Do not load dripping wet clothes into the dryer.
Tumble dry at high heat setting
Tumble dry at low heat setting
Maximum load size
Do not load more than maximum capacity.
These numbers refer to dry weight:
Natural fibres: 6kg max (13lb)
Synthetic fibres: 3kg max (6.6lb)
Items not suitable for tumble drying
●
Articles that containing rubber or rubber-like
materials or plastic film (pillows, cushions, or PVC
rainwear), any other flammable articles or objects
that contain flammable substances (towels soiled
with hair spray).
Glass fibres (certain types of draperies)
Items which have been dry cleaned
! DO NOT overload the dryer as this could result in
reduced drying performance.
Typical load
●
●
Note: 1kg = 1000g
(1lb = 16oz)
150g
●
Items with the ITCL Code
(see Special
Clothes
clothing items). These can be cleaned with special
at-home dry cleaning products. Follow instructions
carefully.
Large bulky items (quilts, sleeping bags, pillows,
cushions, large bedspreads etc). These expand
when drying and would prevent airflow through
the dryer.
Blouse
Cotton
(5oz)
Other
Cotton
Other
100g
500g
350g
700g
(3oz)
Dress
(1lb 2oz)
(12oz)
(1lb 6oz)
●
Jeans
10 nappies
Shirt
1000g (2lb 3oz)
Cotton
Other
300g
200g
125g
(10oz)
(7oz)
(4oz)
T-Shirt
Household Items
Duvet cover
(Double)
Cotton
Other
1500g (3lb 5oz)
1000g (2lb 3oz)
Large Tablecloth
Small Tablecloth
Tea Towel
700g
250g
100g
700g
350g
500g
350g
(1lb 6oz)
(9oz)
(3oz)
Bath Towel
(1lb 6oz)
(12oz)
Hand Towel
Double Sheet
Single Sheet
(1lb 2oz)
(12oz)
At the end of a drying cycle, cottons could still be
damp if you grouped cottons and synthetics together.
If this happens simply give them an additional short
period of drying.
7
Laundry
Special clothing items
Times are approximate and can vary depending
upon:
GB
Blankets and Bedspreads: acrylic items (Acilan,
Courtelle, Orion, Dralon) must be dried with special
care on LOW heat setting. Avoid drying for a long
period of time.
●
Amount of water retained in clothes after spin
cycle: towels and delicates retain a lot of water.
●
Fabrics: items that are the same type of fabric but
Pleated or creased garments: read the manufacturer’s
drying instructions on the garment.
different textures and thicknesses may not have
the same drying time.
●
Starched articles: do not dry these with non-starched
items. Make sure that as much of the starch solution is
removed from the load as possible before placing it in
the dryer. Do not over-dry: the starch will become
powdery and leave your clothing limp, which defeats
the purpose of starch.
Quantity of laundry: single items or small loads
may take longer to dry.
●
Dryness: If you are going to iron some of your
clothes, they can be taken out while still a bit
damp. Others can be left longer if you need them
to be completely dry.
●
Heat setting.
Drying times
●
Room temperature: if the room where the dryer is
The table below presents APPROXIMATE drying times
in minutes. Weights refer to dry garments:
located is cold, it will take longer for the dryer to
dry your clothes.
●
Bulk: some bulky items can be tumble dried with
Cottons
care. We suggest that you remove these items
several times, shake them out, and return them to
the dryer until finished.
High (full) Heat
Drying times 800-1000rpm in washing machine
1kg
2kg
3kg
4kg
5kg
6kg
! Do not over-dry your clothes.
20-30
35-45
45-60 60-70 70-80 80-100
All fabrics contain a little natural moisture, which
keeps them soft and fluffy.
Synthetics
High (full) Heat
Drying times on reduced spin in washing machine
1kg
2kg
3kg
20-30
35-45
45-60
Acrylics
Low (gentle) Heat
Drying times on reduced spin in washing machine
1kg
2kg
25-40
40-60
8
Warnings and Suggestions
To minimise the risk of fire in your tumble dryer, the
! The appliance has been designed and built according
to international safety standards.
These warnings are given for safety reasons and must
be followed carefully.
GB
following should be observed:
●
Tumble dry items only if they have been washed with
detergent and water, rinsed and been through the spin
cycle. It is a fire hazard to dry items that HAVE NOT
been washed with water.
●
Do not dry garments that have been treated with
General safety
chemical products.
Do not tumble dry items that have been spotted or
●
●
This tumble dryer is not intended for use by
soaked with vegetable or cooking oils, this constitutes a
fire hazard. Oil-affected items can ignite spontaneously,
especially when exposed to heat sources such as a tumble
dryer. The items become warm, causing an oxidisation
reaction with the oil, Oxidisation creates heat. If the heat
cannot escape, items can become hot enough to catch
fire. Piling, stacking or storing oil-effected items can prevent
heat from escaping and so create a fire hazard.
If it is unavoidable that fabrics containing vegetable or
cooking oil or those that have been contaminated with
hair care products be placed in a tumble dryer they should
first be washed with extra detergent - this will reduce, but
not eliminate the hazard. The cool tumble phase should
be used to reduce the temperature of the items. They
should not be removed from the dryer and piled or
stacked while hot.
persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
This tumble dryer has been designed for home,
and not professional use.
Do not touch the appliance while barefoot or with
wet hands or feet.
Unplug the machine by pulling on the plug, not
the cord.
Children must not be in proximity of the dryer
when in use. After using the dryer, turn it off and
unplug it. Keep the door closed to make sure that
children do not use it as a toy.
Children should be supervised to ensure that they
do not play with the dryer.
The appliance must be installed correctly and
have proper ventilation. The air intake vents
behind the machine, the outlet vents and the vent
tube should never be obstructed (see Installation).
Never direct the vent tube outlet towards the air
intake at the back of the machine.
Never allow the tumble dryer to recycle exhaust air.
Never use the dryer on carpeting where the pile
height would prevent air from entering the dryer
from the base.
Check to see if the dryer is empty before loading it.
The back of the dryer could become very
hot. Never touch it while in use.
Do not use the dryer unless the filter is securely
in place (see Maintenance).
Do not overload the dryer (see Laundry) for
maximum loads.
Do not load items that are dripping wet.
Carefully check all instructions on clothing labels
(see Laundry).
●
●
●
●
●
Do not tumble dry items that have previously been
cleaned in or washed in, soaked in or soiled with
●
●
petrol/gasoline, dry cleaning solvents or other flammable
or explosive substances. Highly flammable substances
commonly used in domestic environments including
cooking oil, acetone, denatured alcohol, kerosene, spot
removers, turpentine, waxes and wax removers. Ensure
these items have been washed in hot water with an extra
amount of detergent before being dried in the tumble dryer.
●
●
Do not tumble dry items containing foam rubber (also
●
●
known as latex foam), or similarly textured rubber like
materials. Foam rubber materials can, when heated,
produce fire by spontaneous combustion.
●
Fabric softener or similar products should not be used in
●
●
a tumble dryer to eliminate the effects of static electricity
unless the practice is specifically recommended by the
manufacturer of the fabric softener product.
●
●
●
Do not tumble dry undergarments that contain metal
reinforcements eg. bras with metal reinforcing wires.
Damage to the tumble dryer can result if the metal
reinforcements come loose during drying.
●
Do not tumble dry rubber, plastic articles such as shower
●
●
caps or babies waterproof covers, polythene or paper.
●
Do not tumble dry rubber backed articles, clothes fitted
with foam rubber pads, pillows, galoshes and rubber
coated tennis shoes.
●
●
●
●
Do not tumble dry large, very bulky items.
Do not tumble dry acrylic fibres at high temperatures.
Complete each programme with its Cool Tumble Phase.
Do not turn off the dryer when there are still warm
items inside.
Clean the filter after each use (see Maintenance).
Do not allow lint to collect around the dryer.
Never climb on top of the dryer. It could result in
damage.
Always follow electrical standards and requirements
(see Installation).
Always buy original spare parts and accessories
(see Service).
●
Remove all objects from pockets, especially lighters
(risk of explosion).
! WARNING: Never stop the dryer before the end of the
drying cycle unless all items are quickly removed and
spread out so that the heat is dissipated.!
●
●
●
Saving energy and respecting the
environment
●
●
●
Wring out items to eliminate excess water before
tumble drying (if you use a washing machine first,
select a high spin cycle). Doing this will save time
and energy during drying.
●
Always dry full loads - you save energy: single
items or small loads take longer to dry.
●
Clean the filter after each use to contain energy
consumption costs (see Maintenance).
9
Maintenance and Care
Switching off the electricity
Check the drum after each cycle
GB
Unplug your dryer when not using it, when cleaning it
and during all maintenance operations.
Turn the drum manually in order to remove small items
(handkerchiefs) that could have been left behind.
Cleaning the drum
Clean the filter after each cycle
! Do not use abrasives, steel wool or stainless steel
The filter is an important part of your dryer:
cleaning agents to clean the drum.
it accumulates lint and fluff that is formed while drying.
Small items could also become trapped in the filter.
When finished drying, therefore, clean the filter by
rinsing it under running water or with your vacuum
cleaner. Should the filter become clogged up, the airflow
inside the dryer will be seriously compromised: drying
times lengthen and you will consume more energy. It
may also damage your dryer.
A coloured film may start to appear on the stainless
steel drum, this may be caused by a combination of
water and, or cleaning agents such as fabric conditioner
from the wash. This coloured film will not affect the
dryer performance.
Cleaning
The filter is found in front
of the dryer trim
●
External parts in metal or plastic and rubber parts
(see diagram).
can be cleaned with a damp cloth.
●
Periodically check the vent tube and any
permanent venting fixture to make sure that there
has been no accumulation of fluff or lint, and
remove it.
●
Remove lint that collects around the filter and the
outlet vents.
Removing the filter:
1. Pull the plastic grip of
the filter upwards (see
diagram).
! Do not use solvents or abrasives.
! Your dryer uses special bearing components which
do not need lubrication.
2. Clean the filter and
replace it correctly.
Ensure the filter is fully
located flush into the
tumble dryer trim.
! Have your dryer checked regularly by authorised
technicians to ensure electrical and mechanical safety
(see Service).
! Do not use the dryer without replacing the filter..
10
Troubleshooting
One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the
following troubleshooting suggestions:
GB
Problem:
Possible causes / Solution:
●
The dryer won’t start.
The plug is not plugged into the socket, or not making contact.
There has been a power failure.
The fuse has blown. Try to plug another appliance into the socket.
You are using an extension cord? Try to plug the dryer’s power cord
●
●
●
directly into the socket.
The TIMER knob has not been set properly (see Start and Programmes).
The START button has not been pressed (see Start and Programmes).
The START button was pressed with the door open. Make sure the door is
●
●
●
closed before pressing the START button (see Start and Programmes).
! If the START button is pressed with the door open the dryer will not
start. Close the door, wait for a few seconds and then press the START
button again (see Start and Programmes).
●
It is taking a long time to dry.
The filter has not been cleaned (see Maintenance).
The temperature setting is not ideal for the type of fabric you are drying
●
(see Start and Programmes).
The correct programme has not been selected for the load (see Start
●
and Programmes).
The flexible vent tube is obstructed (see Installation).
The air intake vent is obstructed (see Installation).
The permanent ventilation flap on the storm cover is obstructed (see
●
●
●
Installation).
The items were too wet (see Laundry).
The dryer was overloaded (see Laundry).
●
●
11
Service
Before calling the Service Centre:
Spare Parts
GB
●
Use the troubleshooting guide to see if you can
solve the problem yourself (see Troubleshooting).
If not, turn off the dryer and call the Service Centre
closest to you.
This dryer is a complex machine. Repairing it yourself
or having a non-authorised person try to repair it could
cause harm to one or more persons, could damage
the machine and could invalidate the spare parts
warranty.
●
What to tell the Service Centre:
Call an authorised technician if you experience problems
while using the machine.
●
name, address and post code.
telephone number.
the type of problem.
the date of purchase.
●
●
●
●
the appliance model (Mod.).
●
the serial number (S/N).
This information can be found on the data label inside
the door of the machine.
Recycling and Disposal Information
As part of our continued commitment to helping
the environment, we reserve the right to use
quality recycled components to keep down customer
costs and minimise material wastage.
Disposal of old electrical appliances
The European Directive 2012/19/EC on Waste Electrical
and Electronic Equipment (WEEE), requires that old
household electrical appliances must not be disposed
of in the normal unsorted municipal waste stream. Old
appliances must be collected separately in order to
optimise the recovery and recycling of the materials
they contain and reduce the impact on human health
and the environment.
●
Disposing of the packaging material: follow local
regulations, so the packaging can be recycled.
To minimise risk of injury to children, remove the
●
door and plug - then cut off mains cable, flush
with the appliance. Dispose of these parts separately
to ensure that the appliance can no longer be
plugged into a mains socket.
The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that
when you dispose of the appliance it must be
separately collected.
Consumers should contact their local authority or
retailer for information concerning the correct disposal
of their old appliance.
This appliance conforms to the following EC Directives:
- 2006/95/EC (Low Voltage Equipment)
- 2004/108/EC (Electromagnetic Compatibility)
12
GB
13
14
Guarantee
12 months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturers’ guarantee, which covers the cost of
breakdown repairs for twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be
defective because of either workmanship or materials, we will, at our discretion, either
repair or replace the appliance at no cost to you.
The guarantee is subject to the following conditions:
- The appliance has been installed and operated correctly and in accordance with our
operating and maintenance instructions.
- The appliance is only used on the electricity or gas supply printed on the rating plate.
- The appliance has been used for normal domestic purposes only.
- The appliance has not been altered, serviced, maintained, dismantled or otherwise
interfered with by any person not authorised by us.
- Any repair work must be undertaken by us or our appointed agent.
- Any parts removed during repair work or any appliance that is replaced become our
property.
- The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
- Damage resulting from transportation, improper use, neglect or interference or as a
result of improper installation.
- Replacement of any consumable item or accessory. These include but are not limited to:
plugs, cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
- Replacement of any removable parts made of glass or plastic.
THE GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN
COMMERCIAL OR NON-DOMESTIC PREMISES.
Non-Domestic Usage Policy:
Indesit Company manufactures appliances for domestic use only. We understand that in
some cases our appliances are used in commercial and/or non-domestic situations. We
still provide a full 12 month manufacturers’ guarantee, provided the appliance has not been:
Accidentally damaged - Damage that occurs suddenly as a result of an unexpected and
non-deliberate external action.
Maliciously damaged - The deliberate and intentional damage to the product.
Subjected to misuse - Incorrect or careless or improper use.
Subjected to overuse - Excessive usage versus that expected of a domestically situated
appliance.
5 Year Parts Guarantee
Hotpoint also offers you a FREE 5 year parts guarantee. This additional guarantee is
conditional on you registering your appliance with us and the parts being fitted by one
of our authorised engineers. There will be a charge for our engineer’s time.
To activate the extra parts warranty on your appliance, simply call our free phone registration line on
0800 519 2102 (Republic of Ireland 1800 844 347)
15
195067270. 03 N
07/2013 - LION fpg . Four Ashes, Wolverhampton
Extended Guarantees
We offer a selection of protection plans that enable you to fully cover yourself against the expense
of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on
UK: 08448 226 226
Republic of Ireland: 01 230 0233
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint
Service Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone assistance,
or, where necessary, to arrange for an engineer to call.
After Sales Service
No one is better placed to care for your Hotpoint appliance during the course of its
working life than us - the manufacturer.
Essential Contact Information
Hotpoint Service
We are the largest service team in the country offering you access to 400 skilled
telephone advisors and 1100 fully qualified engineers on call to ensure you receive
fast, reliable, local service.
UK: 08448 224 224
Republic of Ireland: 0818 313 413
Please note: Our advisors will require the following information:
Model number
Serial number
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that
protect and hygienically clean your appliance to keep it looking good and functioning
efficiently throughout its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
Appliance Registration
We want to give you additional benefits of Hotpoint ownership.
To activate your FREE 5 year parts guarantee you must register your appliance with us.
Free phone UK: 0800 519 2102
Republic of Ireland: 1800 844 347
Indesit Company UK Limited, Morley Way, Peterborough, PE2 9JB
Indesit Company, Unit 49 Airways Industrial Estate, Dublin 17
|